CYCLONE-User-Manual.pdf - 第46页

User Manual For Cyclone LC Programmers 46 5.2.3.3.3 Set Date Formatting Allows you to select how the date is displayed. The options are: 1. YYYY -MM-DD 2. MM-DD-YYYY 3. DD-MM-YYYY 4. MM/DD/YYYY 5.2.3.3.4 Set T ime Format…

100%1 / 149
User Manual For Cyclone LC Programmers 45
certain that the Cyclone is not set to Dynamic IP mode.
IP
Edit IP Numbers allows the user to set an IP number for the Cyclone. The current IP number is
displayed on the second line. Tap a number to edit and use the touchscreen keyboard to set the
new number. When you are finished, hit Done. If you change your mind and decide not to save, hit
Cancel to leave the IP number as is and return to the Main Menu.
Mask
Edit IP Mask allows the user to set an IP Mask for the Cyclone. The current IP Mask is displayed
on the second line. Use the Up/Down buttons to scroll through the characters. To select a
character, hit the Select button. When you are finished, scroll through the characters until you
reach the -> (right-arrow) character. Selecting this character will complete the process. The default
IP mask is 255.255.255.0.
Gateway
Edit IP Gateway allows the user to set the IP Gateway for the Cyclone. The current IP Gateway is
displayed on the second line. Use the Up/Down buttons to scroll through the characters. To select
a character, hit the Select button. When you are finished, scroll through the characters until you
reach the -> (right-arrow) character. Selecting this character will complete the process.
MAC Address
Show MAC Address displays the current MAC address for the Cyclone.
5.2.3.2.3 Enable/Disable Dynamic IP
Allows the user to toggle the Cyclone configuration between utilizing a Static IP address or a
Dynamic IP address. The user must reset the Cyclone LC after changing from Static to Dynamic
or vice-versa. The reset button on the front side of the unit may be used.
5.2.3.3 Configure Time Settings (Cyclone Time / Real Time Clock)
The Cyclone LC is equipped with a Real Time Clock (RTC) module designed to keep accurate
timing even when the Cyclone is turned off. The Date & Time are displayed on the home screen.
This menu presents options that allow the user to configure the Cyclone’s various date/time/
timezone settings, including formatting options.
5.2.3.3.1 Modify Date / Time
1. Update Time from Internet - Connects to an SNTP server, fetches the current time, and
saves it to the Cyclone. When executed it displays a
message that this can freeze the Cyclone for up to 3
minutes – This is due to an invalid ARP response due to a
bad gateway configuration. Proper configuration will
ensure the problem is resolved. If the network connection
is not configured/connected this displays a message that
the time failed to update. If it is successful no message is
displayed.
2. Set Time Zone Hours - Allows you to set the timezone offset, in hours +/-, from GMT
time
3. Set Time Zone Minutes - Allows you to set the timezone offset, in minutes +/-, from
GMT time
5.2.3.3.2 Set Time-Date Display
Allows you set the Cyclone’s Time-Date Display to one of the following configurations:
1. Display Date Only
2. Display Time Only
3. Display Date and Time
User Manual For Cyclone LC Programmers 46
5.2.3.3.3 Set Date Formatting
Allows you to select how the date is displayed. The options are:
1. YYYY-MM-DD
2. MM-DD-YYYY
3. DD-MM-YYYY
4. MM/DD/YYYY
5.2.3.3.4 Set Time Formatting
Allows you to select how the time is displayed. The options are:
1. HH:MM (24-hour)
2. HH:MM (AM/PM)
3. HH:MM:SS (24-hour)
4. HH:MM:SS (AM/PM)
5.2.3.4 Configure AUX Button
Allows the user to configure an auxiliary (AUX) button which (if configured) will be labeled
appropriately and displayed to the left of the Menu button on the Cyclone’s touchscreen LCD.
When pressed, the AUX button will perform the task for which it has been configured. The options
that may be assigned to the AUX button are:
1. No Operation - No operation is assigned to the AUX button and it will not be displayed on
the LCD screen.
2. Perform Verify Only - Verifies the data on the target device against the data in the pro-
gramming image.
3. Toggle Power - Toggles the Cyclones power relays off/on.
4. Validate Image CRC32 - Validates the CRC32 of the data on the target device against that
of the data in the programming image.
5. Power Cycle Device To Run User Code - Toggles the target power and maintains tri-state
mode for all signals.
6. Launch Image Programming - Launches the selected programming image. Replaces the
hardware Start Button.
5.2.3.5 Configure Screen
This menu presents options that allow the user to adjust or customize the Cyclone’s LCD
touchscreen display in various ways.
5.2.3.5.1 Change Screen Brightness
Allows the user to adjust the brightness of the LCD touchscreen. The “Increase” and “Decrease”
buttons will raise or lower the brightness level, respectively, in increments of 10%. Brightness can
be adjusted from between 100% - 10%. Press “Done” to exit.
5.2.3.5.2 Calibrate Screen
Allows the user to click on specified points on the LCD touchscreen in order to calibrate the
accuracy of the touch function. Follow the on-screen instructions.
5.2.3.5.3 Set Progress Details
This configures the display to present more detailed information during the progress of
programming, including the specific programming steps that are performed and specific
information about the programming and verifying procedure. The user may select “Show Details,
Keep Last Progress On,” “Show Progress Details,” or “Hide Progress Details.”
User Manual For Cyclone LC Programmers 47
5.2.3.5.4 Configure Home Screen
This menu allows you to choose what information to display on Lines 2-8 of the home screen.
Available elements to display consist if information such as: the current IP address, the Cyclone
name, the number of images, etc. In this way the user can customize the display to provide the
information that they find most useful. There is a separate button for each of Lines 2-8. Tapping on
the button for a specific Line brings up a list of elements that you can choose to display on that
Line of the home screen. If the list of elements is greater than one page, tap the More button to
view the rest of the available elements. Tap the element that you want to display on that line and
then tap Done to save your selection.
5.2.3.6 Configure Storage
This menu selection allows the user to format the Cyclone’s internal memory. This menu will also
allow the user to format an SD card located in the Cyclone’s memory expansion slot if the SDHC
Port Activation License is installed. Select “Format Internal Storage” or “Format External SD Card”.
The user will be prompted to ensure that they wish to format the corresponding memory. Tap “Yes”
to format, or “Cancel” to go back to the previous menu option without formatting the memory.
5.2.3.7 Enable/Disable Start Button
This menu option gives the user the option to disable the physical Start Button. Programming can
then be initiated via the Cyclone Control Suite, or by a digital start button on the Cyclone screen if
you have the AUX button set to the "Launch Image Programming" option.
The physical Start Button can always be re-enabled via this same menu toggle.
5.2.4 Status
This menu contains a selection that allow the user to view status information regarding various
aspects of the Cyclone. This menu will likely be expanded with future updates.
5.2.4.1 Show Current IP Settings
Allows the user to view the Cyclone’s Current IP Mode, IP Address, Mask, Gateway, and MAC
Address.