c900773.R02_EN.pdf - 第8页
6 The regenerative register could be high temperature. There is the po ssibility of getting burned if touching a heat sink or regenerative regi ster, so please do not take out or di sassemble covers. The mounter has the …
5
■ Detailed Items
When unloading the mounter, the center of gravity is changed if movable parts have moved,
the mounter might slip from the unloading equipment (forklift) and you might get injured.
Then, XY axes must be fixed by jigs when the machine will be moved.
If the machine has been installed by improper way, the mechanical or electrical problem might be
occurred. Please confirm the machine installation and power cable connection in advance.
The mounter is assumed to be used with linking other machines in line. If the mounter is used by
stand–alone, some covers which satisfy requirements of EN294/JISB9707 mentioned below
have to be arranged and prepared by customer in order to prevent hands from going inside of
openings.
Even using the mounter in line, there might be the opening space at both sides of the board
transfer sections depending on the machine line constitution. In this case, the covers satisfied the
specifications of EN294/JISB9707 have to be fabricated by customer.
The followings are EN294/JISB9707, specifications of safety distance (upper limb) for
clearance.
If feeders are not set on all feeder stations, it is possible to enter hands inside of the machine from
the space of stations which no feeder is set, and then you could get injured.
Therefore, dummy feeders to put on empty stations have to be purchased or some covers satisfied
EN294/JISB9707 have to be prepared for hands not to be able to enter.
Even if the main switch has been turned off, the main power is still supplied from the terminal
XB11 to QS11. There is the possibility of getting electrical shock, so please do not take out or
dissemble covers.
If the machine has UPS option, there is still residual voltage even the main switch has been turned
off. There is the possibility of getting electrical shock, please do to take out or disassemble
covers.
【Specifications of Safety Distance (upper limb) for Clearanc,EN294/JISB9707】
e：Opening Width Opening Part form; Rectangle (Square )
6＜e≦8 ⇒Safety Distance≧20(15)
8＜e≦10 ⇒ ≧80(25)
10＜e≦12 ⇒ ≧100(80)
12＜e≦20 ⇒ ≧120(120)
6
The regenerative register could be high temperature. There is the possibility of getting burned if
touching a heat sink or regenerative register, so please do not take out or disassemble covers.
The mounter has the following warning labels at various parts.
Please follow instructions mentioned in these labels.
7
■ General
Keep the machine and its surrounding area safe and clean.
Do not get on the feeder bank or machine top.
■ Operation
To prevent machine damage, before operation, make sure accessories such as parts feeders are set
completely and not to jump off.
To prevent machine damage, do not operate the mounter with foreign obstacles such as measurement tools
left on the conveyor or feeder bank, linier guides and inside of the tray feeder.
After turning off the mounter, leave the machine 15 seconds or more before turning on again. Otherwise,
motor alarm can result.
To prevent machine damage, do not put foreign obstacles inside of the mounter and tray feeder when
operating the machines by teaching mode.
Do not put the nozzle on the mounting head by hands. If it has not been done properly, the nozzle would hit
with some other parts and the head might be damaged.
Confirm that there is not an obstacle inside of the mounter and tray feeder before pressing Start Switch,
otherwise the machine might be damaged if there is an obstacle.
Confirm that there is not an obstacle inside the mounter and tray feeder when doing ASJ, otherwise the
mounter and tray feeder might be damaged.
Confirm that there is not an obstacle inside of the mounter and tray feeder when doing JOG operation,
otherwise the machine and tray feeder might be damaged.
Please pay attention about the nozzle and nozzle holder height before moving XY axes, they would hit with
the conveyor rail if they are lowered.
Confirm that there is not an obstacle inside of the mounter and tray feeder before taking the origin,
otherwise they would be damaged.
To prevent machine damage, do not put an obstacle inside of the machine and tray feeder when doing
DI/DO operation.
To prevent machine damage, do not put an obstacle inside of the machine and tray feeder when doing
Actuator operation.
Take nozzles out from the mounting heads before doing the vacuum breaking operation, the nozzle would
come off from the head and get damage especially for small size of the nozzle.
To prevent machine damage, do not put an obstacle inside of the machine and tray feeder
To prevent machine damage, do not put an obstacle inside of the machine and tray feeder when warming up
the machine.
Caution