00195722-0102_UM_X-Serie_SR605_EN.pdf - 第310页
4 Setting up and commissioning User Manual SIPLACE X-Series 4.4 Adapting the component trolley to the PCB conveyor height From software version SR.605.xx 07/2008 EN Edition 310 → Lower the co mponent trolley bed slowly u…
User Manual SIPLACE X-Series 4 Setting up and commissioning
From software version SR.605.xx 07/2008 EN Edition 4.4 Adapting the component trolley to the PCB conveyor height
309
4.4.1.1 Warning instructions
WARNING 4
Only SIPLACE engineers or qualified personnel are permitted to adjust the component trolley
height.
→ Always follow the applicable accident prevention regulations.
→ Remove all the feeder modules from the component table, if you want to adjust the height for
the component table.
4.4.1.2 Tools and equipment
You will need the following tools and equipment to adjust the height of the component trolley:
– Hammer
–Punch, 8 mm
– Mounting device (item no. 03015976-xx)
– Lifting device for raising the component trolley table, carrying capacity at least 80 kg
4.4.1.3 Changing the component trolley height
WARNING 4
→ Remove all the feeder modules from the component table.
→ Fit the mounting device to the component table in order to adjust the height. This prevents the
component table becoming deformed when the table is raised or lowered.
→ Fix the assembly guide (item 1 in Fig. 4.4 - 2
, page 310) using the two hexagon socket head
screws M8 x 50 (item 3 in Fig. 4.4 - 2
, page 310) to the component table (item 4 in Fig. 4.4 -
2, page 310).
→ Attach the hooks of the lifting device to the eyelet (item 2 in Fig. 4.4 - 2
, page 310).
→ Raise the component trolley bed slightly to expose the split pins (item 6 in Fig. 4.4 - 2
, page
310
).
→ Use the punch to carefully tap out the split pins on both sides.
→ Insert the spiral clamping pins into the holes for the required PCB conveyor height (see Fig.
4.4 - 1
, page 308).
4 Setting up and commissioning User Manual SIPLACE X-Series
4.4 Adapting the component trolley to the PCB conveyor height From software version SR.605.xx 07/2008 EN Edition
310
→ Lower the component trolley bed slowly until the split pins lie on the supporting blocks (item
5 in Fig. 4.4 - 2
).
→ Dismantle the mounting device
4
Fig. 4.4 - 2 Fixing the assembly guide to the component table of the SIPLACE X component trolley
(1) Mounting device
(2) Eyelet
(3) Hexagon socket head screw DIN 912, M8 x 50, 2 x
(4) M8 threaded hole in the component table, 2x
(5) Supporting block, 2x
(6) Split pin, DIN 7343, 8 x 40 - St, 2 x
User Manual SIPLACE X-Series 4 Setting up and commissioning
From software version SR.605.xx 07/2008 EN Edition 4.4 Adapting the component trolley to the PCB conveyor height
311
4.4.2 Adapting the SIPLACE HF component trolley to the PCB conveyor height
The component trolley for the S feeder modules can be set to the following PCB conveyor heights
with just a few simple actions:
830 mm ± 15 mm (standard height)
900 mm ± 15 mm
930 mm ± 15 mm
950 mm ± 15 mm (SMEMA height) 4
4
Fig. 4.4 - 3 Component trolley (SIPLACE HF-series) with a PCB conveyor height of 950 mm
(1) Holes in the guide columns for the transport heights of 830 to 950 mm
(2) Component trolley table