00195722-0102_UM_X-Serie_SR605_EN.pdf - 第345页
User Manual SIPLACE X-Series 5 Tasks for the operating personnel From software version SR.605.xx 07/2008 EN Edition 5.6 Setting up the feeder modules 345 → Push the le ver (item 5 in Fig . 5.6 - 5 , pa ge 344 ) forward i…
5 Tasks for the operating personnel User Manual SIPLACE X-Series
5.6 Setting up the feeder modules From software version SR.605.xx 07/2008 EN Edition
344
5
Fig. 5.6 - 5 Pick-up window on the tape feeder module
(1) Tape support, removable (see Section 5.6.4.4, page 346)
(2) Pick-up window
(3) Removal edge for the cover foil
(4) Component pick-up area
(5) Lever for raising and latching the pick-up window
→ On the operator panel, press the FORWARD button (item 1 in Fig. 5.6 - 6
) until the bend of
the cover foil is in the component pick-up area (item 4 in Fig. 5.6 - 5
).
5
Fig. 5.6 - 6 Operator panel of the feeder module
(1) FORWARD button for moving the component tape forward
(2) BACK button for moving the component tape back
(3) FOIL button for tensioning the cover foil
User Manual SIPLACE X-Series 5 Tasks for the operating personnel
From software version SR.605.xx 07/2008 EN Edition 5.6 Setting up the feeder modules
345
→ Push the lever (item 5 in Fig. 5.6 - 5, page 344) forward in order to raise the pick-up window
(item 2 in Fig. 5.6 - 5
, page 344) into the first latching position.
→ Pull the cover foil at the side of the pick-up window forward and out underneath the pick-up
window.
→ Fold the cover foil back until it lies against the pull-off edge (item 3 in Fig. 5.6 - 5
, page 344).
PLEASE NOTE 5
Do not lower the pick-up window until the cover foil is lying against the pull-off edge.
→ Push the lever (item 5 in Fig. 5.6 - 5
, page 344) back to lower the pick-up window.
→ Guide the cover foil over the cover foil rocker (item 2 in Fig. 5.6 - 7
) until it reaches the foil
packing wheels (item 1 in Fig. 5.6 - 7
).
5
Fig. 5.6 - 7 Guiding the cover foil to the foil packing wheels
(1) Cover foil packing wheels
(2) cover foil
5
→ On the operator panel, press the FOIL button (item 3 in Fig. 5.6 - 6, page 344) until the cover
foil is tensioned. The cover foil rocker points down and stops the drive motor.
→ Cut the component tape flush with the front end of the feeder module.
5 Tasks for the operating personnel User Manual SIPLACE X-Series
5.6 Setting up the feeder modules From software version SR.605.xx 07/2008 EN Edition
346
5.6.4.4 Tape support for 8 mm X tape feeder module
5
Fig. 5.6 - 8 8 mm X feeder module - tape support and splice sensor
(1) Tape support, removable
(2) Oval opening in the tape support
(3) Splice sensor installation location
The 8 mm X feeder module is equipped with a tape support (item 1 in Fig. 5.6 - 8
). It can easily be
removed if necessary.
→ Insert the tang of a watchmaker's screwdriver into the oval opening (item 2 in Fig. 5.6 - 8
) in
the tape support and pull the tape support out against the direction of travel of the tape.
→ When you insert the tape support, make sure that it engages in its desired position.
PLEASE NOTE 5
For all components size 0402 and smaller, always insert the tape support (item 1 in Fig. 5.6 - 8
)
into the 8 mm X feeder module. This will give you a constant Z pick up height and will minimize
the time needed to correct the pick up heights.