00195722-0102_UM_X-Serie_SR605_EN.pdf - 第344页
5 Tasks for the operating personnel User Manual SIPLACE X-Series 5.6 Setting up the feeder modules From software version SR.605.xx 07/200 8 EN Edition 344 5 Fig. 5.6 - 5 Pick-up window on the tape feeder module (1) T ape…
User Manual SIPLACE X-Series 5 Tasks for the operating personnel
From software version SR.605.xx 07/2008 EN Edition 5.6 Setting up the feeder modules
343
5.6.4.3 Placing tape on the X feeder module
5
Fig. 5.6 - 4 Inserting the component tape
(1) Entry to the tape guide channel
(2) Operator panel
(3) Exit from the tape guide channel
(4) Pick-up window
(5) Lever for raising the pick-up window
5
→ Hold the component tape so that the transport holes are on the left-hand side viewed in the
direction of travel.
→ Push the component tape into the entry (item 1 in Fig. 5.6 - 4
) to the tape guide channel and
further until it emerges from the exit opening (item 3 in Fig. 5.6 - 4
).
→ Pull the component tape up and out, and fold the cover foil back against the top of the tape.
→ Guide the start of the tape beneath the pick-up window (item 2 in Fig. 5.6 - 5
) and further until
the component tape is touching the sprocket wheel.
5 Tasks for the operating personnel User Manual SIPLACE X-Series
5.6 Setting up the feeder modules From software version SR.605.xx 07/2008 EN Edition
344
5
Fig. 5.6 - 5 Pick-up window on the tape feeder module
(1) Tape support, removable (see Section 5.6.4.4, page 346)
(2) Pick-up window
(3) Removal edge for the cover foil
(4) Component pick-up area
(5) Lever for raising and latching the pick-up window
→ On the operator panel, press the FORWARD button (item 1 in Fig. 5.6 - 6
) until the bend of
the cover foil is in the component pick-up area (item 4 in Fig. 5.6 - 5
).
5
Fig. 5.6 - 6 Operator panel of the feeder module
(1) FORWARD button for moving the component tape forward
(2) BACK button for moving the component tape back
(3) FOIL button for tensioning the cover foil
User Manual SIPLACE X-Series 5 Tasks for the operating personnel
From software version SR.605.xx 07/2008 EN Edition 5.6 Setting up the feeder modules
345
→ Push the lever (item 5 in Fig. 5.6 - 5, page 344) forward in order to raise the pick-up window
(item 2 in Fig. 5.6 - 5
, page 344) into the first latching position.
→ Pull the cover foil at the side of the pick-up window forward and out underneath the pick-up
window.
→ Fold the cover foil back until it lies against the pull-off edge (item 3 in Fig. 5.6 - 5
, page 344).
PLEASE NOTE 5
Do not lower the pick-up window until the cover foil is lying against the pull-off edge.
→ Push the lever (item 5 in Fig. 5.6 - 5
, page 344) back to lower the pick-up window.
→ Guide the cover foil over the cover foil rocker (item 2 in Fig. 5.6 - 7
) until it reaches the foil
packing wheels (item 1 in Fig. 5.6 - 7
).
5
Fig. 5.6 - 7 Guiding the cover foil to the foil packing wheels
(1) Cover foil packing wheels
(2) cover foil
5
→ On the operator panel, press the FOIL button (item 3 in Fig. 5.6 - 6, page 344) until the cover
foil is tensioned. The cover foil rocker points down and stops the drive motor.
→ Cut the component tape flush with the front end of the feeder module.