00195722-0102_UM_X-Serie_SR605_EN.pdf - 第417页

User Manual SIPLACE X-Series 6 Station extensions From software version SR.605.xx 07/2008 EN Edition 6.3 Matrix tray changer 417 6.3.3.2 Electrical ratings 6 6.3.3.3 Noise emissions 6 6.3.3.4 Permitted environment al fac…

100%1 / 494
6 Station extensions User Manual SIPLACE X-Series
6.3 Matrix tray changer From software version SR.605.xx 07/2008 EN Edition
416
6.3.3 Technical data
6.3.3.1 Dimensions, weight, other data
6
Tray supply 1 (XL) Tray supply 2
Dimensions
Length x width
Height
1305 x 600 mm²
1490 mm for 830 mm PCB conveyor height
1560 mm for 900 mm PCB conveyor height
1590 mm for 930 mm PCB conveyor height
1610 mm for 950 mm PCB conveyor height
Weight (basic equipment)
Approx. 500 kg (with cassettes and
waffle-pack tray carriers)
Weight (fully equipped) Approx. 534 kg (with components)
Weight (moving mass) Approx. 80 kg Approx. 43.5 kg
Cassette size (L x W x H) 391.2 x 305.6 x 93.3 mm³ 352.7 x 154.8 x 133.8 mm³
Cassette weight
(fully equipped)
(without waffle-pack tray carrier)
Approx. 11 kg
Approx. 1.7 kg
Approx. 7.5 kg
Approx. 1.35 kg
Weight of the
waffle-pack tray carrier
850 g 150 g
Dimensions of the
waffle-pack tray carrier (L x W x H) 386.5 x 295.8 x 11.1 mm³ 371 x 146 x 10.1 mm³
Spacing from one cassette to next 96 mm 135 mm
Distance from level to level 12 mm 11.8 mm
Vertical travel 444 mm (1st to 30th WTC)
a
511.2 mm (1st to 40th WTC
a
)
Horizontal travel between outgoing
and pick-up position Approx. 647 mm Approx. 638 mm
Storage capacity 30 XL waffle-pack tray carri-
ers with 60 JEDEC or
30 special magazines
of maximum size
40 waffle-pack tray carriers
with
40 JEDEC waffle-pack trays
Changeover time (over 5 levels) Approx. 2 s Approx. 1.5 s
Max. height of component and
waffle-pack tray, including
tolerances
All levels filled
One level free
Two levels free
8.5 mm
19.5 mm
31.5 mm
8.5 mm
19.5 mm
-
a) Waffle-pack tray carrier
User Manual SIPLACE X-Series 6 Station extensions
From software version SR.605.xx 07/2008 EN Edition 6.3 Matrix tray changer
417
6.3.3.2 Electrical ratings
6
6.3.3.3 Noise emissions
6
6.3.3.4 Permitted environmental factors
6
6.3.4 Installation notes for the MTC
An MTC may be docked at locations 2 and 4 on all the X-series machines in place of the compo-
nent trolley. To do this, the docking unit installed for the component trolley must be replaced with
the docking unit for the MTC. If you use the MTC at another location, the location that becomes
free may be set up with a component trolley once more.
NOTES 6
For the X2/X3/X4 machines:
– The 20-segment Collect&Place head cannot be used in the vicinity of locations at which an
MTC is docked.
For the X3 and X4 machines:
Supply voltage 3 x 200 VAC ± 5 %; 50/60 Hz (Japanese version)
3 x 208 VAC ± 5%; 50/60 Hz (U.S.A. version)
3 x 400 VAC ± 5%; 50/60 Hz (European version)
Total power 1.5 kW
Rated current 2.7 A at 3 x 400 VAC
4.2 A at 3 x 208 VAC
Fuses 3 x 16 A
Rated power consumption of the largest
consumer
2 A
Max. noise emissions 74 dB (A)
Room temperature Between 15°C and 35°C
Atmospheric humidity
30 - 75 %
(No higher than 45% on average to prevent any pos-
sibility of condensation on the machine)
6 Station extensions User Manual SIPLACE X-Series
6.3 Matrix tray changer From software version SR.605.xx 07/2008 EN Edition
418
– The standard nozzle changer for the TwinHead cannot be used with a combination of Twin-
Head and MTC in placement areas with two gantries. For this situation, there is a nozzle
changer in the placement area with two gantries (see Section 6.1.4.7
, page 402).
For the X2 machines:
– It is not possible to install an MTC and productivity lift at the same time at location 4.
– No nozzle changer can be installed at location 4 in conjunction with the MTC.