FCM_User Reference Manual.pdf.pdf - 第30页
Hu man Inte rfac e User Re ference Manual 4022 5 91 96082 3-14 F CM Mult ifl ex 02.02 3.7 Qu ick Refe r ence o f Human Interface Functions Thi s section gi ves an ov erview of all accessible functions in th e Human Inter…
4022 591 96082 User Reference Manual
02.02 FCM Multiflex 3-13
Human Interface
3.6 On-line Help operation
Depending on the context, on-line help information is available for the user of the
FCM Multiflex system. It can be obtained when pressing function key <F1> after:
■ An FCM Multiflex function has been highlighted in a pull-down menu.
This will give a description of the function itself.
■ Entering a function dialogue.
This will give the following information:
• A description of the function.
• Operating instruction.
• Displayed information.
• Errors which may occur (only if available).
■ An error or warning message is displayed (either immediately after display or
after entering the “Error Recovery” or “FCM Multiflex Warnings” dialogue).
If more than one error and/or warning is displayed, the operator has to select
one first by:
• Pressing the space bar (first item will be highlighted) and moving the ↑ and ↓
cursor keys to the requested message.
• Tapping the touch pad directly on the requested message.
This will give the following information:
• A description of the error/warning.
• Possible cause of the error/warning.
• Possible error recovery method.
Human Interface
User Reference Manual 4022 591 96082
3-14 FCM Multiflex 02.02
3.7 Quick Reference of Human Interface Functions
This section gives an overview of all accessible functions in the Human Interface of
the FCM Multiflex.
FIGURE 3-1 Main Menu
Main
Operator...
Supervisor...
Maintenance/
Entry...
Schedule...
Module Setup... [F8]
Runout...
Abort...
Start... [F5]
Error Recovery... [F3]
FCM Multiflex Warnings... [F4]
LAS
WVM
BVM
BI (optional)
Associate...
Help Index
User
Order
Production
Configuration
ActionSpec
Help
Extended Help
Keys Help
MIS
Edit...
Menu
Stop... [F6]
TC
Copy from Archive...
Copy to Archive...
Maintenance/
Shutdown FCM Multiflex...
FCM Multiflex Base System
WVM
TC
LAS
BVM
BI (optional)
Available Module (LAS) Number(s)
Available Module (WVM) Number(s)
Delete...
Format...
Functions... (see Figure 3-10)
Summary... [F2]
Help for Help
About FCM Multiflex...
Calibration
Calibration - Functions...
System Calibration File
Service Engineer...
Service Functions
Exit
Exit
Exit
Bad Mark Sensing
Fiducial Alignment
Board Vision Module
Options
Edit...
Copy from Archive...
Copy to Archive...
Delete...
Exit
Create Order...
Create System
Calibration File...
Transport Calibration
see Figure 3-9
Video
Online/Offline
Remote/Local
Enable/Disable
Display... [F10]
Fiducial Offset Check
SECS-II / GEM
System Parameters...
HOST
Online/Offline
Remote/Local
Enable/Disable
FCM Base System
4022 591 96082 User Reference Manual
02.02 FCM Multiflex 3-15
Human Interface
FIGURE 3-2 Maintenance/Service Functions
Version...
Date & Time...
Switch to Logger
Switch to NT
Exit
FCM Multiflex
Maintenance /
Processes...
Subsystems...
Exit
Log to Disk
Copy to Archive...
Enable...
Service
Functions
Event Filter
Options
Logfile
Display
General
Edit SMD Info
Copy to Archive...
Delete...
LAS
Copy from Archive...
Module
Command
SMD-Info
Exit
Available Module (LAS) number(s)
Manipulate PPU...
Imagecheck...
Reset controller...
Show placement count...
Dump...
Exchange nozzle...
Show version...
WVM
Module
Command
Exit
Available Module (WVM) number(s)
Manipulate PPU...
Home...
Reset controller...
Show placement count...
Dump...
Exchange nozzle...
Show version...
Vision
Manipulate Vision
Calibrate camera
Set display mode
Edit SMD Info
Copy to Archive...
Delete...
Copy from Archive...
SMD-Info
Servo Amplifiers...
Diagnostics
Offset beam...
TC
Endurance test
Command
Exercise
Servo
Move Hoist...
Index Beam...
Reset controller...
Show version...
Run-in...
SMEMA interface...
Exit
Home...
Run-out...
Calibrate
Adjust Stoppers...
System I/O...
Beam...
Hoist...
Parameters & Data...
Status...
Home...
Base system...
See Figure 3-3