00198783-01_AI_Kit_TwinVHF_Gantry_SXV3_de_en.pdf - 第114页

3 Fitting the gantry 3.2 Gantry Preparations 114 Assembly Instructions / Montageanleitung SIPLACE SX1/SX2 V3 Reconfiguration Kit Twin VHF mit Portal Reconfiguration Kit Twin VHF with Gantry 06/2020 Locking the gantry car…

3 Fitting the gantry

3.2 Gantry Preparations

Assembly Instructions / Montageanleitung SIPLACE SX1/SX2 V3 Reconfiguration Kit Twin VHF mit Portal

Reconfiguration Kit Twin VHF with Gantry 06/2020

113

Move the gantry lift into position

Fig.28: Gantry lift in position

► Carefully move the gantry lift (1) up to

the gantry.

 CAUTION!

Take care not to damage the gantry

when moving it with the gantry lift.

Do not hit the gantry or locks with the

gantry carrier plate(3).

Make sure that the gantry carrier plate

(3) protrudes above the gantry carrier

locks(4).

► Remove the foam cover (2).

3.2.3 Locking and Transporting the Gantry Carrier

The "gantry 40 mm" may only be transported with the current gantry carriers [00519814-03]

(observe function state!).

Move the gantry lift to the gantry

Fig.29: Gantry lift on gantry

► Move the gantry carrier plate (2) for the

gantry lift over the gantry carrier locks

(3)

. The groove (1) must be able to en-

gage with the two locking plates (3)

► Lower the gantry lift so that the gantry

carrier plate can slide into the locks (4)

► Move the lift only so far down that the

locking lever (5)

can be closed.

3 Fitting the gantry

3.2 Gantry Preparations

114 Assembly Instructions / Montageanleitung SIPLACE SX1/SX2 V3 Reconfiguration Kit Twin VHF mit Portal

Reconfiguration Kit Twin VHF with Gantry 06/2020

Locking the gantry carrier

Fig.30: Locked gantry carrier

► Press the lock (4) back and pull (1) the

handle (2)

of the lock upwards.

ð The lever (3) will engage. The

spring on the lock (4)

secures the

locking mechanism.

Locking the gantry carrier correctly

Fig.31: Checking the lock

► Check that the lever (2) on the lock (1)

has engaged properly.

► To open, press the lock backwards and

then press the lever downwards. This

opens the lock.

Securing the gantry in the transportation crate

Fig.32: Fuse in the transportation crate

► The gantry is fixed with four screws (1)

in the transportation crate. Remove

these screws.

 CAUTION!

Only transport the gantry with the

gantry lift when the arms are locked!

► Move the gantry lift upwards and care-

fully lift the gantry out of the transporta-

tion crate.

 NOTICE!

The placement head must be in the

center of the gantry.

This ensures that the load is distrib-

uted evenly during transportation.

3 Fitting the gantry

3.2 Gantry Preparations

Assembly Instructions / Montageanleitung SIPLACE SX1/SX2 V3 Reconfiguration Kit Twin VHF mit Portal

Reconfiguration Kit Twin VHF with Gantry 06/2020

115

3.2.4 Transportation Locks and Tilt Guard

Fig.33: Transportation locks

The gantry is locked with three transportation

locks (1)

and (3) at the gantry carrier. In addi-

tion, the head plate has two transportation

locks (2)

for the placement head.

CAUTION

Docking

► Flap down the transportation lock plates right before the docking.

► Make sure that the gantry does not slide off the gantry carrier during rerailing respectively

derailing and that the tilt guard is suspended in order to hold the gantry in position.

► Move the green lever upwards and swivel the transportation lock to one side.

► There is another lever at (3). Move the green lever upwards and remove it.

► Loosen the two screws fastening the transportation locks (2) to the head plate in each case

and remove both locks.

NOTICE

Storing the transportation locks

If the gantry is transported or packed back into the transportation crate, you need to refit the

transportation locks.

► Place the transportation locks in the crate for later usage.

Tilt guard on the gantry carrier

Fig.34: Tilt guard on the gantry carrier

The gantry is also fitted with a tilt guard (1) on

the gantry carrier.

 CAUTION!

Tilt guard on the gantry carrier

When the tilt guard is open, the gantry

could fall off the gantry carrier.

Only open the tilt guard once you have

hooked the gantry carrier onto the

machine docking unit.

NOTICE

Tilt guard on the gantry

The tilt guard may need to be adjusted to the gantry type "standard gantry" or "40mm VHF

Twin gantry". For more details see the technical information "Description of correct pack-

aging for an SX gantry" [DE:TI2013‑05D06] [EN:TI2013‑05E06].