00198783-01_AI_Kit_TwinVHF_Gantry_SXV3_de_en.pdf - 第122页

3 Fitting the gantry 3.5 Installing the Gantry 122 Assembly Instructions / Montageanleitung SIPLACE SX1/SX2 V3 Reconfiguration Kit Twin VHF mit Portal Reconfiguration Kit Twin VHF with Gantry 06/2020 Buffer types Fig.48…

3 Fitting the gantry

3.5 Installing the Gantry

Assembly Instructions / Montageanleitung SIPLACE SX1/SX2 V3 Reconfiguration Kit Twin VHF mit Portal

Reconfiguration Kit Twin VHF with Gantry 06/2020

121

Fig.46: Flat ribbon cable and pneumatic connections

► Carefully place the flat ribbon cable (1)

and the pneumatic connections (2) over

the gantry.

► Remove the black plastic foil. A cable

tie fixes the black plastic foil to the trail-

ing cable(3)

3.5.1 Replacing/Fitting the End Position Buffers

Overview

Fig.47: Upgrade to SIPLACE SX2

1. Location 1

2. Location 2

3. Safety switch

4. Buffer with distance pipe at a SIPLACE

SX1

Standard: 226.5 mm

Twin VHF: 174 mm

5. Short buffer on an SX2 (standard and

Twin VHF)

When upgrading from a SIPLACE SX1 to a SIPLACE SX2, you need to fit the short end position

buffers at location 2.

When downgrading from a SIPLACE SX2 to a SIPLACE SX1, fit the buffer with distance pipe at

location 2.

When fitting a 40mm gantry, you need to fit the buffer with distance pipe at location 2 of the

SIPLACE SX1. (Buffer labeling: "LOC2,VHFSX1").

3 Fitting the gantry

3.5 Installing the Gantry

122 Assembly Instructions / Montageanleitung SIPLACE SX1/SX2 V3 Reconfiguration Kit Twin VHF mit Portal

Reconfiguration Kit Twin VHF with Gantry 06/2020

Buffer types

Fig.48: Buffer types

1. Standard: long buffer with distance pipe

for location 2 of an SX1 (226.5mm)

2. Twin VHF: buffer with shortened dis-

tance pipe [03105259-xx] for location 2

of an SX1 (174mm)

Buffer labeling: "LOC2, VHF SX1

3. Standard and Twin VHF: short buffer

with rubber damper for both locations

on an SX2 (35mm)

Machine SIPLACE SX1 SIPLACE SX2

Location 1 Location 2 Location 1 Location 2

Standard 35 mm rubber

dampers

226.5 mm

distance pipe

35 mm rubber

dampers

35 mm rubber

dampers

40 mm gantry for

Twin VHF

35 mm rubber

dampers

174 mm distance

pipe (shortened)

LOC2, VHF SX1

35 mm rubber

dampers

35 mm rubber

dampers

Installation

NOTICE

Holder and distance pipe

► You might need to fit the holder from one distance pipe onto the other distance pipe.

When doing so, hand-tighten

the distance pipe on the holder.

Fig.49: Fitting the end position buffer

► Fit the end position buffer (2) to the left

side.

► Fit the end position buffer (3) to the

right side. The safety switch (4)

for the

buffer monitoring function must engage

in the Schmersal switch.

► Tighten the fastening screws (1) for the

buffers with a torque of 14Nm

3 Fitting the gantry

3.6 Connecting the Trailing Cable

Assembly Instructions / Montageanleitung SIPLACE SX1/SX2 V3 Reconfiguration Kit Twin VHF mit Portal

Reconfiguration Kit Twin VHF with Gantry 06/2020

123

3.6 Connecting the Trailing Cable

Fig.50: Cover

► Remove the cover (1) over the gantry

interface. To do this, remove the two

fastening screws on the right side and

carefully open the bottom left pushbut-

ton.

Fig.51: Fitting the trailing cable

► Fit the trailing cable holder (1) from

below, to the gantry distributor holder.

See the following section.

► Carefully place the flat ribbon cable and

the pneumatic hoses to one side (2)

► Make sure you do not damage the

cables and hoses.

► Take care that the alignment is correct

and that all cables and hoses are run

above one another and evenly.

 NOTICE!

Use the correct gantry with Gig E trail-

ing cable, since only this can be con-

nected as described. It is not possible

to connect an older gantry with hotlink

trailing cable.

Fig.52: Heat-shrinkable hose

 NOTICE!

When fitting the trailing cable, make

sure that the heat-shrinkable sleeve

(1) protects the flat ribbon cable under

the Y sensor module holder.