N7201A654E.pdf - 第198页

NPM- TT2 EJM1EE-MB-02 T-02 Motor Number Error Reset Process Error Servo Process Error Motor Object Not Exist Nozzle shaft drop Error Messag e Troubleshooting 2-1-4 Emergency stop errors 14 Error Code Error Message Cause …

100%1 / 332
NPM-TT2 EJM1EE-MB-02T-02
Tape Float
Driver Software Interlock
Solutions to errors
Error Code
Error Message
Cause Inspection and Solution
Servo driver of the target axis
is at fault.
(Driver software interlock
occurred.)
Check the situation of the error
occurred and error message, and
contact PFSC.
1513
The tape cover sensor is
blocked.
(Interlock occurred.)
Take any of the following measures:
1) Close the front cover of the tape
feeder.
2) Set the toggle lever of the tape
feeder properly.
3) Make sure that detection area of
the tape cover sensor is not
blocked by the cover tape or big
component.
4) Choose [Machine] - [Adjust] - [All]
- [Input confirm] and check that the
feeder opening sensors 1 to 4 of
the table are OFF when the light
from the emitter is blocked and ON
when the light from the emitter
reaches the detector. At this time,
make also sure that the green LED
is lit when the light from the emitter
is blocked and the green and red
LEDs are lit when the light from
the emitter reaches the detector.
1514
2-1-4-25
NPM-TT2 EJM1EE-MB-02T-02
Motor Number Error
Reset Process Error
Servo Process Error
Motor Object Not Exist
Nozzle shaft drop
Error
Messag
e
Troubleshooting
2-1-4
Emergency stop errors 14
Error Code
Error Message
Cause Inspection and Solution
Nozzle shaft may be locked
at the lowered position.
(Nozzle shaft drop error
occurred.)
Do not move the head in X/Y
direction. Raise the nozzle shaft by
hand.
1515
Servo driver of the target axis
is at fault.
(No motor object.)
Check the situation of the error
occurred and error message, and
contact PFSC.
1521
Servo driver of the target axis
is at fault.
(Servo process error
occurred.)
Check the situation of the error
occurred and error message, and
contact PFSC.
1522
Servo driver of the target axis
is at fault.
(Reset process error
occurred.)
Check the situation of the error
occurred and error message, and
contact PFSC.
1523
Servo driver of the target axis
is at fault.
(Motor number error
occurred.)
Check the situation of the error
occurred and error message, and
contact PFSC.
1524
2-1-4-26
NPM-TT2 EJM1EE-MB-02T-02
Position Error Interrupt
Exclusive Process Error
Return To Origin Process
Error
Motion Process Error
Motion Preparation Error
Solutions to errors
Error Code
Error Message
Cause Inspection and Solution
Servo driver of the target axis
is at fault.
(Operation preparation error
occurred.)
Check the situation of the error
occurred and error message, and
contact PFSC.
1525
Servo driver of the target axis
is at fault.
(Operation process error
occurred.)
Check the situation of the error
occurred and error message, and
contact PFSC.
1526
Servo driver^ motor or origin
sensor of the target axis is at
fault.
(Origin return process error
occurred)
Check the situation of the error
occurred and error message, and
contact PFSC.
1527
Servo driver of the target axis
is at fault.
(Exclusive process error
occurred.)
Check the situation of the error
occurred and error message, and
contact PFSC.
1528
Unwanted interrupt occurred
during positioning of XY unit.
(Position interrupt error
occurred.)
1) Restart the machine.
2) If the error persists, contact PFSC.
1529
2-1-4-27