N7201A654E.pdf - 第236页
NPM- TT2 EJM1EE-MB-02 T-02 Communication : (Common Slave): Parameter Error Communication : (Common Slave): Command Error Communication : ROM Update Coun t Error Communication : Specified File Close Error Communication : …
NPM-TT2 EJM1EE-MB-02T-02
Communication: Specified
File Size Acquire Error
Communication: Specified
File Open Error
Communication: Status
Communication Error
Communication: Status
Communication Stopping
Error
Communication:
Completion Error
Solutions to errors
Error Code
Error Message
Cause Inspection and Solution
Improper procedure was
taken in software processing.
(Transmission command not
executed properly.)
Close the error screen and restart
production. Then, check the
situation of the error occurred and
error message, and contact PFSC.
1739
Improper procedure was
taken in software processing.
(Function to obtain status
was called while status
communication was
stopped.)
Close the error screen and restart
production. Then, check the
situation of the error occurred and
error message, and contact PFSC.
1740
Improper procedure was
taken in software processing.
(Error occurred in status
communication.)
Close the error screen and restart
production. Then, check the
situation of the error occurred and
error message, and contact PFSC.
1741
Improper procedure was
taken in software processing.
(Cannot open ROMless file.)
Close the error screen and restart
production. Then, check the
situation of the error occurred and
error message, and contact PFSC.
1742
Improper procedure was
taken in software processing.
(Improper ROMless file size.)
Close the error screen and restart
production. Then, check the
situation of the error occurred and
error message, and contact PFSC.
1743
2-1-4-63
NPM-TT2 EJM1EE-MB-02T-02
Communication:
(Common Slave):
Parameter Error
Communication:
(Common Slave):
Command Error
Communication: ROM
Update Count Error
Communication: Specified
File Close Error
Communication: Specified
File Size Read Error
Error
Messag
e
Troubleshooting
2-1-4
Emergency stop errors 33
Error Code
Error Message
Cause Inspection and Solution
Improper procedure was
taken in software processing.
(Cannot read the ROMless
file size.)
Close the error screen and restart
production. Then, check the
situation of the error occurred and
error message, and contact PFSC.
1744
Improper procedure was
taken in software processing.
(Failed to close ROMless
file.)
Close the error screen and restart
production. Then, check the
situation of the error occurred and
error message, and contact PFSC.
1745
Writing to FROM exceeded
the limit.
(ROMless count exceeded
the specified write count.)
Contact PFSC.
1746
Improper procedure was
taken in software processing.
(Undefined command
issued.)
Close the error screen and restart
production. Then, check the
situation of the error occurred and
error message, and contact PFSC.
1747
Improper procedure was
taken in software processing.
e.g.: 2 has been set although
available parameter is 0 or 1.
(Invalid parameter setting.)
Close the error screen and restart
production. Then, check the
situation of the error occurred and
error message, and contact PFSC.
1748
2-1-4-64
NPM-TT2 EJM1EE-MB-02T-02
Feeder Number Set Error
NG Eject Conveyor Action
Timeout
Communication:
(Common Slave):
Undefined Error
Communication:
(Common Slave): System
Section Error
Communication:
(Common Slave):
Communication Error
Solutions to errors
Error Code
Error Message
Cause Inspection and Solution
Check sum error occurred in
the communication data from
the head or feeder cart to the
host.
(Communication error
occurred.)
Clean the drawer connectors for
connecting modules, and check the
wiring connected to them. If the
error persists, contact PFSC.
1749
Embedded software for each
board may be damaged.
(Check sum error occurred in
ROMless file.)
Read the ROMless file again and
restart production. Then, check the
situation of the error occurred and
error message, and contact PFSC.
1750
Improper procedure was
taken in software processing.
(Undefined error occurred.)
Close the error screen and restart
production. Then, check the
situation of the error occurred and
error message, and contact PFSC.
1751
NG eject conveyor failed to
finish operation within the
prescribed time.
(NG eject conveyor failed to
operate properly.)
Check the NG eject conveyor for
proper movement using the
switches.If not, contact PFSC.
1752
Improper procedure was
taken in software processing.
(Feeder number error
occurred.)
Check the situation of the error
occurred and error message, and
contact PFSC.
1756
2-1-4-65