N7201A654E.pdf - 第262页

NPM- TT2 EJM1EE-MB-02 T-02 IspBox MainSys PCB sk ip notification comma nd error Camera IF board DMA transfer error Camera IF board Exposure finish information deal error Camera IF board Exposure finish information start …

100%1 / 332
NPM-TT2 EJM1EE-MB-02T-02
Camera IF board Camera
parameter set error
Camera IF board Light
spot correction table set
error
Camera IF board Binary
table set error
Camera IF board Camera
capture parameter error
Camera IF board
Initialization error
Solutions to errors
Error Code
Error Message
Cause Inspection and Solution
Capture board could not be
initialized.
(Failed to initialize the
camera IF board.)
Check the connection of the camera
link cable between the inspection
head and inspection box.
1901
Improper procedure was
taken in software processing.
(Failed to obtain the capture
parameter.)
Restart the machine. If the error
persists, contact PFSC.
1902
Improper procedure was
taken in software processing.
(Failed to set the binary table
of the camera IF board.)
Restart the machine. If the error
persists, contact PFSC.
1903
Improper procedure was
taken in software processing.
(Failed to set the light spot
correction table of the
camera IF board.)
Restart the machine. If the error
persists, contact PFSC.
1904
Improper procedure was
taken in software processing.
(Failed to set the camera
parameters of the camera IF
board.)
Restart the machine. If the error
persists, contact PFSC.
1905
2-1-4-89
NPM-TT2 EJM1EE-MB-02T-02
IspBox MainSys PCB skip
notification command
error
Camera IF board DMA
transfer error
Camera IF board
Exposure finish
information deal error
Camera IF board
Exposure finish
information start error
Error
Messag
e
Troubleshooting
2-1-4
Emergency stop errors 46
Error Code
Error Message
Cause Inspection and Solution
Improper procedure was
taken in software processing.
(Failed to set the exposure
completion notice of the
camera IF board.)
Restart the machine. If the error
persists, contact PFSC.
1906
Exposure finish information
could not be received.
(Failed to receive the
exposure completion notice
of the camera IF board.)
Check the connection of the camera
link cable.
1907
Image transfer from the
camera IF board to the
inspection box PC failed.
(Failed in DMA transfer of
image from the camera IF
board.)
Check the connection of the camera
link cable.
1908
Improper procedure was
taken in software processing.
(PCB skip information
command notified
incorrectly.)
Restart the machine. If the error
persists, contact PFSC.
1909
2-1-4-90
NPM-TT2 EJM1EE-MB-02T-02
System state error
Command error
IspBox MainSys APC-
MFB file make error
IspBox SubSys Sample
image save error
IspBox take image start
timeout
Solutions to errors
Error Code
Error Message
Cause Inspection and Solution
Because the IspBOX
process is delayed^ it has
been over the specified time
at the start of taking image.
(Image is taken in inspect
head after the light is off.)
Please restart the auto running. If
the error persists, contact PFSC.
1910
Needful image data lost in
saving sample image.
(Failed to save the sample
image.)
It is possible that the recognition is
wrong in the mark recognition
process.Please confirm the mark
recognition process.
1911
(1)Can't communicate with
the LNB.(2)The remain
capacity of the hard disk is
not enough.(3)The file
system is in a incorrect
situation.
(Failed to make the APC-
MFB file.)
(1)Please confirm connection to the
network.(2)Please confirm the
remain capacity of the hard disk on
IspBox and LNB.Then restart the
machine.If it happened again.
Please inform the manufacturer.
1912
VLC system may be at fault.
(Command error detected by
VLC.)
Contact PFSC.
1951
VLC system may be at fault.
(System error detected by
VLC.)
Contact PFSC.
1952
2-1-4-91