N7201A654E.pdf - 第264页

NPM- TT2 EJM1EE-MB-02 T-02 Low light intensity Effective Section overflow Line number overflow Sensor Blocked completely Communication error Error Messag e Troubleshooting 2-1-4 Emergency stop errors 47 Error Code Error …

100%1 / 332
NPM-TT2 EJM1EE-MB-02T-02
System state error
Command error
IspBox MainSys APC-
MFB file make error
IspBox SubSys Sample
image save error
IspBox take image start
timeout
Solutions to errors
Error Code
Error Message
Cause Inspection and Solution
Because the IspBOX
process is delayed^ it has
been over the specified time
at the start of taking image.
(Image is taken in inspect
head after the light is off.)
Please restart the auto running. If
the error persists, contact PFSC.
1910
Needful image data lost in
saving sample image.
(Failed to save the sample
image.)
It is possible that the recognition is
wrong in the mark recognition
process.Please confirm the mark
recognition process.
1911
(1)Can't communicate with
the LNB.(2)The remain
capacity of the hard disk is
not enough.(3)The file
system is in a incorrect
situation.
(Failed to make the APC-
MFB file.)
(1)Please confirm connection to the
network.(2)Please confirm the
remain capacity of the hard disk on
IspBox and LNB.Then restart the
machine.If it happened again.
Please inform the manufacturer.
1912
VLC system may be at fault.
(Command error detected by
VLC.)
Contact PFSC.
1951
VLC system may be at fault.
(System error detected by
VLC.)
Contact PFSC.
1952
2-1-4-91
NPM-TT2 EJM1EE-MB-02T-02
Low light intensity
Effective Section overflow
Line number overflow
Sensor Blocked
completely
Communication error
Error
Messag
e
Troubleshooting
2-1-4
Emergency stop errors 47
Error Code
Error Message
Cause Inspection and Solution
Connector may be
disconnected.
(Communication error
detected by VLC.)
Check the connection connector.
1953
1) Sensor is blocked
completely by some
obstacles.
2) Connector may be
disconnected.
(VLC sensor blocked
completely.)
1) Remove any obstacles. Wipe
away any dirt from the lens if it is
dirty.
2) Check the connector.
1954
VLC system may be at fault.
(Line overflow detected by
VLC.)
Contact PFSC.
1955
VLC system may be at fault.
(Overflow from effective zone
detected by VLC.)
Contact PFSC.
1956
Lens may be dirty.
(Drop in intensity detected by
VLC.)
Clean the lens if dirt is found.
1957
2-1-4-92
NPM-TT2 EJM1EE-MB-02T-02
Sensor Blocked partly
Outlines overflow
System error
Head unconnected
Displacement of the
optical axis detected
Solutions to errors
Error Code
Error Message
Cause Inspection and Solution
Optical axis is displaced.
(Displacement of the optical
axis detected.)
Check the installation condition of
the VLC sensor.
1958
VLC system may be at fault.
(Unconnected head
detected.)
Contact PFSC.
1959
VLC system may be at fault.
(System error detected.)
Contact PFSC.
1960
VLC system may be at fault.
(Shell count detected by VLC
overflowed.)
Contact PFSC.
1961
Any of the following causes
is likely:
1) Sensor is blocked partly
by some obstacles.
2)Connector may be
disconnected.
(VLC sensor blocked partly.)
Take measures shown with the
same number as that of the cause.
1)Remove any obstacles. Wipe
away any dirt from the lens if it is
dirty.
2) Check the connector.
1962
2-1-4-93