00196504-02_UM_X-Serie_SR70X_EN.pdf - 第184页
Technical data for the machine User manual SIPLACE X-series X feeder modules From software version SR.70x.xx 01/2011 EN edition 184 3.9.3 X linear dipping unit (LDU X) Item no. 001 1701 1-xx Linear dip module for flux / …
User manual SIPLACE X-series Technical data for the machine
From software version SR.70x.xx 01/2011 EN edition X feeder modules
183
3.9.2.10 88 mm X tape feeder module
3
Fig. 3.9 - 12 88 mm X tape feeder module
3
3
88 mm X tape feeder module item no. 00141278-xx
88 mm X tape feeder module with splice sensor item no. 00141298-xx
Width 105.2 mm
Feeder module locations filled 9
Conveyor increment from 4 mm to 96 mm in 4 mm increments
Changeover time for the component tape < 45 s
Changeover time for the preset feeder module
on the machine
≤ 8 s
Technical data for the machine User manual SIPLACE X-series
X feeder modules From software version SR.70x.xx 01/2011 EN edition
184
3.9.3 X linear dipping unit (LDU X)
Item no. 00117011-xx Linear dip module for flux / LDU-X
Item no. dip plates see Section 3.9.3.5
, page 186
3
Fig. 3.9 - 13 Linear Dipping Unit (LDU X)
(1) LDU X
(2) Dip plate
(3) Flux container
(4) Display panel (4 lines each with 20 characters)
(5) Operator panel with 6 membrane keys
(6) LED for status displays
(7) EMERGENCY OFF button
3.9.3.1 Description
The X linear dipping unit (item 1 in Fig. 3.9 - 13) is used to wet flip-chip and CSP components with
flux. The flux container item 3 in Fig. 3.9 - 13
) slides with a linear movement over the dip plate
(item 2 in Fig. 3.9 - 13
) and applies the flux at a defined layer thickness in the depression in the
dip plate. The parameters for wetting a component with flux are prescribed in SIPLACE Pro. The
User manual SIPLACE X-series Technical data for the machine
From software version SR.70x.xx 01/2011 EN edition X feeder modules
185
component is wetted and then the flux layer is renewed. This sequence guarantees consistent
processing conditions for the components.
The individual menus for actions and operating parameters are displayed in the display panel
(item 4 in Fig. 3.9 - 13
, page 184). The menus can be selected or a parameter modified and stored
using the buttons on the operator panel (item 5 in Fig. 3.9 - 13
, page 184). The 4 LEDs (item 6 in
Fig. 3.9 - 13
, page 184) of the display panel signalizes the status of the LDU-X. The LDU-X is
switched off immediately when the emergency stop button is pressed (item 7 in Fig. 3.9 - 13
, page
184
).
The LDU-X is suitable for both the MultiStar and the TwinStar. It is added to the set-up as a stand-
alone feeder module type. The module can only be set up on a component trolley of the SIPLACE
X-series. An implemented warming function allows the viscosity of the flux to be altered. The LDU-
X can be operated outside the machines using the energy and data interface for X feeder modules
(see Section 3.9.5
, page 191) for test purposes.
3.9.3.2 Technical data
Further technical data and details can be found in the "SIPLACE LDU-X" user manual.
May be installed on the following machines SIPLACE X4I, X4, X3, X2
Filled 8mm locations on the CO trolley of the
SIPLACE X-series
9
Component size a max. of 55 x 55 mm², depending on the
placement head type;
a max. of 45 x 45 mm² for TwinStar
The adjustable flux layer thickness 15 - 260 μm
Tolerance of the layer thicknesses ± 5 μm ... ± 10 µm
Time for applying the flux to the dip plate > 3s
Component dipping time adjustable using the software
Flux Indium TACFlux 010 / 013
Kester TSF-6502 / 6522
Alphametals OM338 / OM338PT
Almit BM1 RMA
Cookson WS 3018lv
et al.
Possible placement heads MultiStar, SpeedStar, TwinStar