00196504-02_UM_X-Serie_SR70X_EN.pdf - 第238页
Setting up and commissioning User manual SIPLACE X-series Setting up the machine From software version SR.70x.xx 01/2011 EN edition 238 → Remove the cab le covers (items 3 and 5 in Fig . 4.3 - 7 , p age 237 ) from the ra…
User manual SIPLACE X-series Setting up and commissioning
From software version SR.70x.xx 01/2011 EN edition Setting up the machine
237
4.3.6 Fitting the output conveyor
4.3.6.1 Tools
– Allen keys, DIN 911, set
– Phillips screwdriver, size 1
4.3.6.2 Assembly
4
Fig. 4.3 - 7 Output conveyor - dual conveyor
(1) Rail, output conveyor
(2) Rail, processing conveyor 2
(3) Cable cover 20 x 200
(4) Countersunk screw, ISO 7046, M3x6, 2x per cable cover
(5) Cable cover 20 x 310
(6) Fillister head screw DIN 912, M3x5, 1x per cable cover
(7) Fillister head screw DIN 912, M6x16, and washer, 4x per rail
(8) Guide for hexagonal shaft
(9) Hexagonal shaft (single conveyor: one, dual conveyor: two)
(10) Drive unit
Setting up and commissioning User manual SIPLACE X-series
Setting up the machine From software version SR.70x.xx 01/2011 EN edition
238
→ Remove the cable covers (items 3 and 5 in Fig. 4.3 - 7, page 237) from the rails (item 1 in Fig.
4.3 - 7
, page 237) of the output conveyor.
→ Carefully place the rail (item 1 in Fig. 4.3 - 7
, page 237) against the rail on the processing
conveyor (item 2 in Fig. 4.3 - 7
, page 237).
CAUTION 4
Be careful not to cut through any of the light barrier or drive motor cables.
→ Fix each rail using 4 fillister head screws M6x16 and the associated washers (item 7 in Fig.
4.3 - 7
, page 237).
→ Connect the power cable to the light barriers and drive motors.
→ Fix the cable covers in place (item 3 and 5 in Fig. 4.3 - 7
, page 237).
→ Introduce the hexagonal shaft (item 9 in Fig. 4.3 - 7
, page 237) into the drive unit (item 10 in
Fig. 4.3 - 7
, page 237).
→ Make sure that the hexagonal shaft guide (item 8 in Fig. 4.3 - 7
, page 237) always points to-
wards the conveyor side wall to which the drive unit (item 10 in Fig. 4.3 - 7
, page 237) is fixed.
4.3.7 Fitting the extension kit on the PCB output side
4.3.7.1 Tools
– Allen keys, DIN 911, set
– Machine key
User manual SIPLACE X-series Setting up and commissioning
From software version SR.70x.xx 01/2011 EN edition Setting up the machine
239
4.3.7.2 Assembly
4
Fig. 4.3 - 8 Fitting the extension kit on the PCB output side
(1) Extension kit
(2) Door
(3) Fillister head screw DIN 912, M6x16 and washer
(4) Ground connection point
(5) Conveyor cover
(6) Side panel, detached
(7) Drawer unit rail
(8) Axis unit, gantries 1 and 3 (X2), axis unit, gantry 3 (X3) or axis unit, gantries 2 and 3 (X4)