00197446-02_UM_JTF_S_JTF-M_ X-Serie_S_de_en.pdf - 第99页
Operational Safety 2.1.4 Warning Labels Safety Instructions JEDEC Tray Feeder 99 2.1.3.3 2 . 1 . 3 . 3 S a f e t y o f P la n t a n d E q u ip m e n t Safety of Plant and Equipment ► Never make changes, however minor, un…
Operational Safety
Safety Instructions 2.1.3 Important Notes on Operational Safety
98 JEDEC Tray Feeder
► If you need to work on the machine and you do not have adequately trained personnel at your com-
pany, always call in a service engineer from ASM Assembly Systems GmbH & Co. KG! ASM Assem-
bly Systems GmbH & Co. KG will not accept liability for any damage or consequential damage that
is the result of incorrect work!
► If particularly hazardous situations are identified while the module is in use, the module owner must
immediately notify the manufacturer in writing so that appropriate action can be taken to reduce the
potential danger.
See also
2.1.4.2 Warning, Prohibition and Cautionary Labels [ ➙ 99]
2.1.3.2
2.1.3.2 Safety of Operators and Other Persons
Safety of Operators and Other Persons
► Module operators may only carry out work for which they have been adequately trained and with
which they are totally familiar!
► NEVER open one of the covers if you are not totally familiar with the use and functioning of the mod-
ule! Do not open the covers during operation unless you are told to do so in this Manual or in the
station software dialog!
► For your own safety, wear work clothes that conform to the guidelines of the professional associa-
tion, i.e. no wide sleeves etc.
► Reduce the risks by not wearing scarves, chains or ties at your work post.
► People with long hair must wear a protective head covering.
See also
2.1.4 Warning Labels [ ➙ 99]
WARNING
Safe operation of module
In spite of all the safety precautions taken by the manufacturer, failure to use the module as
prescribed can result in severe physical injury and/or considerable damage to equipment! For
the module to be safe, it must be used correctly by qualified personnel and all warnings must
be observed. Some work requires training that goes beyond the scope of this Manual.
WARNING
Voltage
The module is electrically driven. When electrical devices are in use, certain parts carry dan-
gerous voltage levels!
► Before performing any work to parts which conduct electricity, switch the machine off at the
main switch and unplug the Lemosa socket for the adapter, to disconnect the power be-
tween the module and the machine (see View From the Rear).
⇨ There is a risk of death, severe injury and/or considerable damage to equipment if these
instructions are not followed.
1. Lemosa socket
Operational Safety
2.1.4 Warning Labels Safety Instructions
JEDEC Tray Feeder 99
2.1.3.3
2.1.3.3 Safety of Plant and Equipment
Safety of Plant and Equipment
► Never make changes, however minor, unless you are totally aware of the effect they will have on the
overall functioning of the module and system!
► The modules must always be set up, retooled and maintained by appropriately trained personnel.
► Do not make modifications to the safety equipment. In particular, NEVER deactivate circuit-breakers
or remove safety devices.
2.1.4
2.1.4 Warning Labels
Warning Labels
The warning labels are made from soft PVC film, and are abrasion-proof, light-fast and resistant to water
and weathering.
2.1.4.1
2.1.4.1 Warning Labels on the SIPLACE JTF-S
Warning Labels on the SIPLACE JTF-S
2.1.4.2
2.1.4.2 Warning, Prohibition and Cautionary Labels
Warning, Prohibition and Cautionary Labels
There are two warning labels on the sides of the
SIPLACE JTF-S.
CAUTION
Danger of crushing
Reaching in here can lead to injuries to the arms and hands.
➢ No reaching into the module while it is running.
► Do not reach into the module while it is running.
WARNING
Damage to warning labels
Incorrect cleaning can damage the warning labels.
➢ Using the correct cleaning agents.
► Do not use abrasive cleaners or solvents for cleaning warning labels.
► Replace any damaged or illegible warning labels.
► Check that the warning labels are positioned correctly.
Operational Safety
Safety Instructions 2.1.5 Danger of Crushing at SIPLACE JTF-S
100 JEDEC Tray Feeder
2.1.5
2.1.5 Danger of Crushing at SIPLACE JTF-S
Danger of Crushing at SIPLACE JTF-S
The SIPLACE JTF-S (JEDEC tray stack feeder) stops
when the stop button (1) is pressed or if the door is unin-
tentionally opened.
DANGER
Danger of crushing
There is a risk of injuries by pinch points or a risk of crushing by reaching into the feeder or from
loose clothing which could get into the feeder during operation.
➢ Observe correct handling and the safety instructions.
► Do not reach into the feeder while it is running.
► Maintain an adequate safety distance.