03217917-01-01E By DEK Technical Reference Manual Vol 1_enPDFA.pdf - 第202页

15 BOARD STOP 15.6 ADJUSTMENTS AND SETTINGS 202 TECHNICAL REFERENCE MANUAL Vol 1 E By DEK 04/2019 7 6 4 5 ► Rotate the reed switch (6) and adjustable stop (4) anti-clockwise until the adjustable stop (4) abuts the fixed …

100%1 / 292
15 BOARD STOP
15.6 ADJUSTMENTS AND SETTINGS
TECHNICAL REFERENCE MANUAL Vol 1 E By DEK 04/2019 201
15.6.2.2 RHS Configuration
The remote board stop is configured for the RHS when:
●
The board stop rotates clockwise to the raised position and faces the rear of the machine
when lowered, as shown below.
●
The adjustable stop is positioned between the fixed stop and the reed switch.
1
3
A B
2
A Remote Board Stop
RHS Configured
2 Fixed Stop
B View on Rear of Rotary Actuator 3 Reed Switch
1 Adjustable Stop
To achieve this carry out the following:
► With the board stop in the position shown below, slacken the two grub screws (3) using a
2mm Allen key.
► Without moving the drive shaft, rotate the rotary arm (1) and board stop (2) 90 degrees anti-
clockwise, so that the board stop is vertical. Tighten the two grub screws (3).
2
1
2
3
► Using the access hole in the side of the remote board stop assembly, slacken the adjustable
stop (4) securing screw (7).
15 BOARD STOP
15.6 ADJUSTMENTS AND SETTINGS
202 TECHNICAL REFERENCE MANUAL Vol 1 E By DEK 04/2019
7
6
4
5
► Rotate the reed switch (6) and adjustable stop (4) anti-clockwise until the adjustable stop (4)
abuts the fixed stop (5).
► Tighten the adjustable stop securing screw (7) through the access hole.
LH
RH
5
6
5
4
► Continue with the appropriate one of the following procedures:
●
15.6.5 "Camera to Remote Board Stop - RHS Configuration" [}210]
●
15.6.6 "Remote Board Stop - LHS to RHS Configuration" [}214]
15 BOARD STOP
15.6 ADJUSTMENTS AND SETTINGS
TECHNICAL REFERENCE MANUAL Vol 1 E By DEK 04/2019 203
15.6.3 Setting the Remote Board Stop
WARNING
BOARD CLAMPS. EXTREME CARE MUST BE EXERCISED WHEN WORKING IN
THE TOOLING AREA OF THE MACHINE TO AVOID INJURY. THE FOILS ON THE
FRONT AND REAR BOARD CLAMPS ARE VERY SHARP.
This adjustment sets the position and the height of the remote board stop with respect to the
product board to be printed.
► Select Open Cover Commands.
► Select Unload Screen.
► Open the printhead cover.
► Remove the screen from the machine.
► Mark the centre point, in the X axis, on the front of the product board.
► Select Board Clamps to release the clamps.
► Place the product board on the rails with the board centre point at the Camera Reference Po-
sition (white dot on front rail).
► Select Board Clamps to clamp the board in place.
► Close the printhead cover.
► Press the System button.
► Select Back.
► Select Setup Product.
► Select Tooling and make a note of the value of the Under Clearance parameter.
► Select Back.
► Select Back.
► Select Maintenance.
► Select Diagnostics.
► Use Next or Previous to highlight Rising Table.
► Select Select Module.
► Use Next or Previous to highlight Raise Table To Vision Height.
► Select Run Diagnost. The table is driven to vision height and the board is clamped.
► Use Next or Previous to highlight Drive Table Using Jog Buttons.
► Select Run Diagnost.
► Remove one of the safety covers to gain access to the rail height adjusters.