03217917-01-01E By DEK Technical Reference Manual Vol 1_enPDFA.pdf - 第257页

16 TRANSPORT RAILS MODULE 16.5 REPLACEMENT PROCEDURES TECHNICAL REFERENCE MANUAL Vol 1 E By DEK 04/2019 257 NOTE With Auto Rail Width set to Disabled the rear rail does not set the board width, but it can still be moved …

100%1 / 292
16 TRANSPORT RAILS MODULE
16.5 REPLACEMENT PROCEDURES
256 TECHNICAL REFERENCE MANUAL Vol 1 E By DEK 04/2019
► Remove the securing screws (1) from the front board clamp and remove the board clamp.
► Fit the appropriate snugger base plate to the rear rail and secure using the M4 pan head
screws.
► Fit the appropriate front snugger plate to the front rail and secure using the M4 pan head
screws.
► Fit the rear snugger plate (4), don’t tighten the M4 pan head securing screws.
7
4
5
6
4 Rear Snugger Plate 6 Downstops
5 Front Snugger Plate 7 Snugger Base Plate
► Close the front printhead cover.
► Press the System button.
► Locate the magnetic plate on the right hand side of the machine containing the pneumatics for
the snuggers.
8
9
8 Pneumatic Switch 9 View on Right Hand Side of Ma-
chine
► Turn the pneumatic switch On.
► Load the product file to be printed, the rear rail moves to set the board width.
16 TRANSPORT RAILS MODULE
16.5 REPLACEMENT PROCEDURES
TECHNICAL REFERENCE MANUAL Vol 1 E By DEK 04/2019 257
NOTE
With Auto Rail Width set to Disabled the rear rail does not set the board width, but it can still be
moved in diagnostics.
► Select Maintenance.
► Select Machine Setup.
► Select Basics.
► Select Clamp Type.
► Select Snuggers.
► Select Accept.
► Select Back.
► Select Back.
► Select Back.
► Carry out 16.4.7 "Board to Snugger Gap" [}249].
16.5.4 Snuggers to Board Clamps
WARNING
BOARD CLAMPS. EXTREME CARE MUST BE EXERCISED WHEN WORKING IN
THE TOOLING AREA OF THE MACHINE TO AVOID INJURY. THE FOILS ON THE
FRONT AND REAR BOARD CLAMPS ARE VERY SHARP.
NOTE
This procedure is valid when converting to either board clamps or foil-less clamps.
► Select Open Cover Commands.
► Select Carriage To Rear.
► Select Unload Screen.
► Open the front printhead cover.
► Remove the stencil from the machine.
► On the rear rail, remove the two rear snugger plate securing screws (4) and remove the rear
snugger plate (5).
6
4
1
2
3
5
1 Rear Snugger Base Plate 4 Rear Snugger Plate Securing
Screws
2 Front Snugger Plate 5 Rear Snugger Plate
3 Front Snugger Plate Securing
Screws
6 Rear Snugger Base Plate Secur-
ing Screws
16 TRANSPORT RAILS MODULE
16.5 REPLACEMENT PROCEDURES
258 TECHNICAL REFERENCE MANUAL Vol 1 E By DEK 04/2019
► On the rear rail, remove the snugger base plate securing screws (6) and remove the snugger
base plate (1).
► On the front rail, remove the front snugger plate securing screws (3) and remove the front
snugger plate (2).
► Fit the board clamp to the rear rail and secure using the M4 pan head screws.
► Fit the board clamp to the front rail and secure using the M4 pan head screws.
► Foil-less clamps only. Fit the appropriate foil-less clamp to the rear rail and secure using the
M4 pan head screws.
► Foil-less clamps only. Fit the appropriate foil-less clamp to the front rail and secure using the
M4 pan head screws.
► Locate the magnetic plate on the right hand side of the machine containing the pneumatics for
the snuggers.
7
8
7 Pneumatic Switch 8 View on Right Hand Side of Ma-
chine
► Turn the pneumatic switch (7) On.
► Select Maintenance.
► Select Machine Setup.
► Select Basics.
► Select Clamp Type.
► Select Board Clamps.
► Select Accept.
► Select Back.
► Select Back.
► Select Back.
► Foil-less clamps only. Carry out 16.4.4 "Foil-less Clamp Height Adjustment" [}242].
NOTE
The Board Clamp Setting procedure is not required after snugger to board clamp/foil-less clamp re-
placement.