CP40 service manual.pdf - 第49页
MODULE ERROR CODE Symptom and Cause ACTION Service Manual $119, 0, "[PCB] ", "Fiducial Mark Type=%d Fiducial Mark No.=%d " Length IY value of PCB Fiducial Mark is incorrect. Length IY value of PCB Fid…
MODULE
ERROR
CODE
Symptom and Cause ACTION
Service
Manual
$104, 0,
"[PCB] ", "Fiducial Mark Type=%d Fiducial Mark No.=%d "
Y value of part original point is incorrect.
Y value of part original point shall be in system area.
Abnormal condition occurs to X value of Placement Origin in "PCB Setup/Board-Definition" Dialog
Box of MMI.
$105, 0,
"[PCB] ", "Fiducial Mark Type=%d Fiducial Mark No.=%d "
X value of wait position is incorrect.
X value of wait position shall be in a system area.
If <Auto> check box of "PCB Setup/Board Definition" Dialog Box of MMI is checked, try again with
not checked condition.
$106, 0,
"[PCB] ", "Fiducial Mark Type=%d Fiducial Mark No.=%d "
Y value of wait position is incorrect.
Y value of wait position shall be in a system area.
If <Auto> check box of "PCB Setup/Board Definition" Dialog Box of MMI is checked, try again with
not checked condition.
$107, 1,
"[PCB] ", "Fiducial Mark Type=%d Fiducial Mark No.=%d "
Height of Z axis to use for moving a system is incorrect.
Adjust the value of <Moving Height> Edit Box in "PCB Setup/Board Definition" of MMI in accordance
with followings.
$108, 1,
"[PCB] ", "Fiducial Mark Type=%d Fiducial Mark No.=%d "
Fixer type is incorrect.
Select the suitable Fixer Type.
$109, 1,
"[PCB] ", "Fiducial Mark Type=%d Fiducial Mark No.=%d "
Bad mark logic is incorrect.
Select the correct Bad Mark Logic.
$110, 0,
"[PCB] ", "Fiducial Mark Type=%d Fiducial Mark No.=%d "
X value of bad mark is incorrect.
X value of Bad Mark shall be in PCB area. (Refer to EDIT)
$111, 0,
"[PCB] ", "Fiducial Mark Type=%d Fiducial Mark No.=%d "
Y value of bad mark is incorrect.
Y value of Bad Mark shall be in PCB area.
$112, 1,
"[PCB] ", "Fiducial Mark Type=%d Fiducial Mark No.=%d "
Fiducial Mark type is incorrect.
Select the suitable Fiducial Mark Type.
$113, 1,
"[PCB] ", "Fiducial Mark Type=%d Fiducial Mark No.=%d "
Fiducial Mark type is incorrect.
Select the correct Fiducial Mark Type.
$114, 0,
"[PCB] ", "Fiducial Mark Type=%d Fiducial Mark No.=%d "
X value of No.1 Fiducial Mark is incorrect.
X value of No.1 Fiducial Mark shall be in PCB area.
$115, 0,
"[PCB] ", "Fiducial Mark Type=%d Fiducial Mark No.=%d "
Y value of No. 1 Fiducial Mark is incorrect.
Y value of No.1 Fiducial Mark shall be in PCB area.
$116, 0,
"[PCB] ", "Fiducial Mark Type=%d Fiducial Mark No.=%d "
X value of No. 2 Fiducial Mark is incorrect.
X value of No.2 Fiducial Mark shall be in PCB area.
$117, 0,
"[PCB] ", "Fiducial Mark Type=%d Fiducial Mark No.=%d "
Y value of No. 2 Fiducial Mark is incorrect.
Y value of No.2 Fiducial Mark shall be in PCB area.
$118, 0,
"[PCB] ", "Fiducial Mark Type=%d Fiducial Mark No.=%d "
Length IX value of PCB Fiducial Mark is incorrect.
Length IX value of PCB Fiducial Mark shall be 0.1~10mm.
- 36 -
MODULE
ERROR
CODE
Symptom and Cause ACTION
Service
Manual
$119, 0,
"[PCB] ", "Fiducial Mark Type=%d Fiducial Mark No.=%d "
Length IY value of PCB Fiducial Mark is incorrect.
Length IY value of PCB Fiducial Mark shall be 0.1~10mm.
$120, 0,
"[PCB] ", "Fiducial Mark Type=%d Fiducial Mark No.=%d "
Width dX value of PCB Fiducial Mark is incorrect.
Width dX value of PCB Fiducial Mark shall be 0.1~10mm.
$121, 0,
"[PCB] ", "Fiducial Mark Type=%d Fiducial Mark No.=%d "
Width dY value of PCB Fiducial Mark is incorrect.
Width dY value of PCB Fiducial Mark shall be 0.1~10mm.
$122, 1,
"[PCB] ", "Fiducial Mark Type=%d Fiducial Mark No.=%d "
Scan speed of PCB Fiducial Mark is incorrect.
Scan speed of PCB Fiducial Mark shall be 1~100mm/s.
$123, 1,
"[PCB] ", "Fiducial Mark Type=%d Fiducial Mark No.=%d "
Type or ID of PCB Fiducial Mark is incorrect.
Select the suitable Fiducial Mark Types(Circle, Square, Cross).
PMT Error
Code Table
$124, 1,
"[PCB] ", "Fiducial Mark Type=%d Fiducial Mark No.=%d "
No. of split board is incorrect.
No. of split board shall be 1~500.
$126, 1,
"[PCB] ", "Fiducial Mark Type=%d Fiducial Mark No.=%d "
Slowdown factor is incorrect.
Select the suitable Slowdown parameter.
$1100,
"[PCB] ", "Split No.=%d "
Offset X value of split board is incorrect.
Split board offset X value shall be in PCB area.
$1126, 0,
"[PCB] ", "Split No.=%d "
Offset X value of split board is incorrect.
Split board offset X value shall be in PCB area.
$1127, 0,
"[PCB] ", "Split No.=%d "
Offset Y value of split board is incorrect.
Split board offset Y value shall be in PCB area.
$1128, 0,
"[PCB] ", "Split No.=%d "
Angle of split board is incorrect.
Angle of split board shall be degree of 0, 90, 180, 270, -90, -180 and -270.
$200,
$201, 0,
$202, 0,
"[Step Program] ", "Cycle=%d Head=%d "
Y value of placement point is incorrect.
Y value of plancement point shall be in PCB area.
$203, 0,
"[Step Program] ", "Cycle=%d Head=%d "
R value of placement angle is incorrect.
R value of placement angle shall be degree of -360~+360.
$204, 0,
"[Step Program] ", "Cycle=%d Head=%d "
Placement height is incorrect.
Placement height shall be -3~15mm.
$205, 1,
"[Step Program] ", "Cycle=%d Head=%d "
Feeder type is incorrect.
Select the suitable Feeder type. 12-3-1
"[Step Program] ", "Cycle=%d Head=%d "
X value of placement point is incorrect.
X value of plancement point shall be in PCB area.
- 37 -
MODULE
ERROR
CODE
Symptom and Cause ACTION
Service
Manual
$206, 1,
"[Step Program] ", "Cycle=%d Head=%d "
No. of Stick Unit is incorrect.
Stick Unit No. shall be 1~10.
$207, 1,
"[Step Program] ", "Cycle=%d Head=%d "
No. of Tray Unit is incorrect.
Tray Unit No. shall be 1~3.
Click <Tray Feeder> button of <Setup/PCB Setup(Feeder)>.
$208, 1,
"[Step Program] ", "Cycle=%d Head=%d "
No. of Tape Feeder is incorrect.
Tape Feeder No. shall be 1~52.
4-3-2
4-3-5
$209, 1,
"[Step Program] ", "Cycle=%d Head=%d "
Stick No. is incorrect.
Stick No. shall be 1~10.
$210, 1,
"[Step Program] ", "Cycle=%d Head=%d "
Tray No. is incorrect.
Tray No. shall be 1~5 (for Single Tray) and 1~20 (for Multi Tray).
$211, 1,
"[Step Program] ", "Cycle=%d Head=%d "
ANC No. is incorrect.
ANC No. shall be 1~4. 4-3-4
$212, 1,
"[Step Program] ", "Cycle=%d Head=%d "
ANC Hole No. is incorrect.
ANC Hole No. shall be 1~20 (for 20-hole ANC), 1~10 (for 10-hole ANC) and 1~2 (for Gripper ANC).
$213, 1,
"[Step Program] ", "Cycle=%d Head=%d "
ANC Type No. is incorrect.
Select the suitable ANC Type.
$214, 1,
"[Step Program] ", "Cycle=%d Head=%d "
Skip Flag is incorrect.
Select the suitable Skip Flag.
Select the point to skip below SK in <Setup/PCB Setup(Step Program) and input Y to the point.
$215, 1,
"[Step Program] ", "Cycle=%d Head=%d "
Fiducial Mark data is incorrect.
Select the suitable Fiducial Mark.
$216, 1,
"[Step Program] ", "Cycle=%d Head=%d "
Fiducial Mark type is incorrect.
Select the suitable Fiducial Mark Type.
$217, 0,
"[Step Program] ", "Cycle=%d Head=%d "
X value of No. 1 Fiducial Mark is incorrect.
X value of No. 1 Fiducial Mark shall be in PCB area.
$218, 0,
"[Step Program] ", "Cycle=%d Head=%d "
Y value of No. 1 Fiducial Mark is incorrect.
Y value of No. 1 Fiducial Mark shall be in PCB area.
$219, 0,
"[Step Program] ", "Cycle=%d Head=%d "
X value of No. 2 Fiducial Mark is incorrect.
X value of No.2 Fiducial Mark shall be in PCB area.
$220, 0,
"[Step Program] ", "Cycle=%d Head=%d "
Y value of No. 2 Fiducial Mark is incorrect.
Y value of No.2 Fiducial Mark shall be in PCB area.
$221, 0,
"[Step Program] ", "Cycle=%d Head=%d "
Length IX value of Fiducial Mark is incorrect.
Length IX value of Fiducial Mark shall be 0.1~10mm.
$222, 0,
"[Step Program] ", "Cycle=%d Head=%d "
Length IY value of Fiducial Mark is incorrect.
Length IY value of Fiducial Mark shall be 0.1~10mm.
- 38 -