bnp-b2365(eng)b.pdf - 第188页
3. Setup 3 - 101 No. Abbr. Parameter name Details Setting rang e (Unit) Standard setting SP229 OXSFT Orientation virtual target shift amount Set the amount to shift the target position when orientation virtual target pos…
3. Setup
3 - 100
No. Abbr. Parameter name Details
Setting range
(Unit)
Standard
setting
<For MDS-C1-SP/SPH/SPM>
Set to reduce the noise generated from the spindle motor
Set the band of the low path filter
0 to 2250
(rad/s)
0
SP213 LPF
Low path filter
<For MDS-C1-SPX/SPHX>
Not used. Set to "0".
0 0
SP214 TZRN
Synchronized tapping
control
zero point return speed
This parameter is valid when SP193 (SPECT)/bit E is set
to "0".
Set the zero point return speed used when the speed loop
changes to the position loop.
0 to 500
(r/min)
50
SP215 TPDT
Synchronized tapping
control
zero point return
deceleration rate
This parameter is valid when SP193 (SPECT)/bit E is set
to "0".
Set the deceleration rate where the machine starts to
decelerate when it returns to the target stop point during
synchronized tapping zero point return.
When the machine tends to overshoot at the stop point
set a smaller value.
0 to 10000
(pulse)
1
SP216 TPST
Synchronized tapping
control
zero point return shift
amount
This parameter is valid when SP193 (SPECT)/bit E is set
to "0".
Set the synchronized tapping zero point position.
0 to 4095 0
SP217 TINP
Synchronized tapping
control
in-position width
Set the position error range for output of the in-position
during synchronized tapping control.
1 to 2880
(1/16 deg)
16
SP218 TODR*
Synchronized tapping
control
excessive error width
Set the excessive error width during synchronized
tapping.
0 to 32767
(pulse)
(1 pulse =
0.088 deg)
32767
SP219 IQGT*
Synchronized tapping
control
current loop gain
magnification 1
Set the magnification of current loop gain (torque
component) during synchronized tapping control.
1 to 1000 (%) 100
SP220 IDGT*
Synchronized tapping
control
current loop gain
magnification 2
Set the magnification of current loop gain (excitation
component) during synchronized tapping control.
1 to 1000 (%) 100
SP221 PG2T
Synchronized tapping
control
position loop gain 2
Set the second position loop gain when high-gain control
is applied during synchronized tapping control.
When this parameter is not used, set to "0".
0 to 999
(rad/s)
0
SP222 PG3T
Synchronized tapping
control
position loop gain 3
Set the third position loop gain when high-gain control is
applied during synchronized tapping control.
When this parameter is not used, set to "0".
0 to 999
(rad/s)
0
SP223 SPDV Speed monitor speed
Set the spindle limit speed in the door open state.
(Invalid when 0 is set.)
If the spindle end speed exceeds this setting value when
the door is open, the speed monitor error (5E) will occur.
0 to 800
(r/min)
0
SP224 SPDF Speed monitor time
Set the time (continuous) to detect alarms.
(Detected instantly when 0 is set.)
0 to 2813
(3.5 ms)
0
SP225 OXKPH
Position loop gain
magnification after
orientation completed
(H coil)
0 to 2560
(1/256-fold)
0
SP226 OXKPL
Position loop gain
magnification after
orientation completed
(L coil)
0 to 2560
(1/256-fold)
0
SP227 OXVKP
Speed loop proportional
gain magnification after
orientation completed
0 to 2560
(1/256-fold)
0
SP228 OXVKI
Speed loop cumulative
gain magnification after
orientation completed
If gain changeover is valid (SP097: SPEC0/bitC=1) during
orientation control, set the magnification of each gain
changed to after orientation completed.
0 to 2560
(1/256-fold)
0
Parameters with an asterisk * in the abbreviation, such as OSP*, are validated with the NC power turned ON again.
3. Setup
3 - 101
No. Abbr. Parameter name Details
Setting range
(Unit)
Standard
setting
SP229 OXSFT
Orientation virtual target
shift amount
Set the amount to shift the target position when
orientation virtual target position is valid (SP097:
SPEC0/bitD=1).
0 to 2048
(360 deg/4096)
0
<For MDS-C1-SPH>
Set the ratio of iron loss to all losses when temperature
compensation considering iron loss is valid.
0 to 100
(%)
0
SP230
WIH
Iron loss compensation
value
<For MDS-C1-SP/SPX/SPHX/SPM>
Not used. Set "0".
0 0
<For MDS-C1-SPH>
Set the primary-delay time constant to detect overload 2
0 to 60
(min)
0
SP231
OL2T Overload 2 time constant
<For MDS-C1-SP/SPX/SPHX/SPM>
Not used. Set "0".
0 0
SP232 Not used. Set "0". 0 0
SP233 JL*
Disturbance observer
Load inertia rate
Set "the motor inertia + motor axis conversion load inertia"
in respect to the motor inertia.
SV037 (JL) =
Jl + Jm
Jm
× 100
Jm : Motor inertia
Jl : Motor axis conversion load inertia
0 to 5000 (%) 0
SP234 OBS1*
Disturbance observer
low path filter frequency
Set the frequency of the low path filter for when the
disturbance observer is valid.
0 to 1000
(rad/s)
0
SP235 OBS2*
Disturbance observer
gain
Set the gain for the disturbance observer.
0 to 500 (%) 0
SP236 OBS3 Fixed control constant Set by Mitsubishi. Set "0" unless designated in particular. 0 0
<For MDS-C1-SPM>
The following value is judgment value for spindle speed
overrun (alarm 3E).
The speed command + SP237 × 0.125 [r/min]
0 to 32767
(r/min)
0
SP237
KSCP*
Spindle speed overrun
judgment value
<For MDS-C1-SP/SPH/SPX/SPHX>
Not used. Set "0".
0 0
<For MDS-C1-SPM>
The following value is judgment value for speed excessive
deflection 2 (alarm 3F).
The speed command × SP238 / 100 [r/min]
0 to 100
(%)
0
SP238
SE2R
Speed excessive
deflection 2
detection range
<For MDS-C1-SP/SPH/SPX/SPHX>
Not used. Set "0".
0 0
<For MDS-C1-SPM>
Set the continuous detection time for speed excessive
deflection 2 (alarm 3F).
0 to 3000 0
SP239
SE2T
Speed excessive
deflection 2
detection time
<For MDS-C1-SP/SPH/SPX/SPHX>
Not used. Set "0".
0 0
<For MDS-C1-SPX/SPHX>
This validates the automatic adjustment function for the
PLG connected to the MDS-B-PJEX.
0 to 1
0 → 1
SP240 EXHS
PLG automatic
adjustment (PJEX)
<For MDS-C1-SP/SPH/SPM>
Not used. Set "0".
0 0
<For MDS-C1-SPX/SPHX>
This changes the spindle drive unit type, serial NO. and
software version display.
"0" Displays the details for the spindle drive unit.
"1" Displays the details for the detector converter.
0 to 1 0
SP241 EXBIT
Spindle monitor
changeover
<For MDS-C1-SP/SPH/SPM>
Not used. Set "0".
0 0
SP242 Vavx Fixed control constant Set by Mitsubishi. Set "0" unless designated in particular. 0 0
SP243 UTTM Fixed control constant Set by Mitsubishi. Set "0" unless designated in particular. 0 0
SP244 OPLP Fixed control constant Set by Mitsubishi. Set "0" unless designated in particular.
Parameters with an asterisk * in the abbreviation, such as OSP*, are validated with the NC power turned ON again.
3. Setup
3 - 102
No. Abbr. Parameter name Details
Setting range
(Unit)
Standard
setting
<For MDS-C1-SP/SPH/SPM>
This validates the automatic adjustment function for the
PLG.
0 to 1
0 → 1
SP245 PGHS
PLG automatic
adjustment
<For MDS-C1-SPX/SPHX>
Not used. Set "0".
0 0
SP246 TEST Fixed control constant Set by Mitsubishi. Set "0" unless designated in particular. 0 0
SP247 Not used. Set "0". 0 0
SP248 Not used. Set "0". 0 0
SP249 SMO Speed meter speed
Set the motor rotation speed when the speed meter 10V
is output.
When set to "0", this parameter becomes the same as
SP017 (TSP).
0 to 32767
(r/min)
0
SP250 LMO Load meter voltage
Set the voltage when the load meter 120% is output.
When set to "0", this becomes 10V.
0 to 10 (V) 0
SP251 Not used. Set "0". 0 0
SP252 Not used. Set "0". 0 0
SP253 DA1NO
D/A output channel 1
data number
Set the output data number for channel 1 of the D/A
output function.
When set to "0", the output is speedometer.
-32768 to
32767
0
SP254 DA2NO
D/A output channel 2
data number
Set the output data number for channel 2 of the D/A
output function.
When set to "0", the output is speedometer.
-32768 to
32767
0
SP255 DA1MPY
DA output channel 1
magnification
Set the data magnification for channel 1 of the D/A output
function.
The output magnification is the setting value divided by
256.
When set to "0", the output magnification becomes 1-fold,
in the same manner as when "256" is set.
-32768 to
32767
(1/256-fold)
0
SP256 DA2MPY
DA output channel 2
magnification
Set the data magnification for channel 2 of the D/A output
function.
The output magnification is the setting value divided by
256.
When set to "0", the output magnification becomes 1-fold,
in the same manner as when "256" is set.
-32768 to
32767
(1/256-fold)
0
Parameters with an asterisk * in the abbreviation, such as OSP*, are validated with the NC power turned ON again.