Utah-94-721002-System-Manual.pdf - 第29页
Health and Safety lñÑçêÇ=fåëíêìãÉåíë=mä~ëã~=qÉÅÜåçäçÖó= mä~ëã~ä~Ä and fçåÑ~Ä Syste m ve nt gas : Nitrog en Max inlet pressur e : 5 Bar WAR NI NG Warns of gas type and maximum pr essure, connected to the system. Gas t y p…
mä~ëã~ä~Ä and fçåÑ~Ä lñÑçêÇ=fåëíêìãÉåíë=mä~ëã~=qÉÅÜåçäçÖó= Health and Safety
NKQ= t~êåáåÖ=~åÇ=~Çîáëçêó=ä~ÄÉäë=
During manufacture, warning and advisory labels are attached to the system to indicate
potential hazards and components, which should not be operated or maintained without first
reading the relevant manual. Typical labels and their meanings are as follows:
DANGER
RF ENERGY
Disconnect
electrical supply
before servicing
Danger of physical injury from RF radiation or from touching
components within the labelled equipment.
PINCH POINT
Keep hands away
from chamber lid
when closing.
WARNING
Danger of trapping limbs, fingers etc. in the labelled equipment.
WARNING
STRONG
MAGNETIC FIELD
Avoid contact with
this area.
Danger of physical injury from the Strong Magnetic Field generated by
the labelled equipment.
WARNING
HOT SURFACE
Do not touch
Caution, hot surface IEC 417, No. 5041
DANGER
LOW TEMPERATURE
Wear thermal
protective gloves
Danger of physical injury, from the labelled equipment.
WARNING
SERVICE BY
QUALIFIED STAFF
ONLY
Refer to manual
Read the relevant manual before proceeding to operate or maintain the
labelled equipment.
WARNING
RF & UV RADIATION.
DO NOT USE THIS PORT
FOR VIEWING WITH THE
NAKED EYE
WITHOUT MESH
SHIELD IN PLACE
Danger of physical injury from RF and UV radiation from the labelled
components.
WARNING
LASER BEAM
Disconnect
electrical supply
before servicing
Danger of physical injury from Laser Beam generated by the labelled
components.
Health and Safety
Issue 11: August 2004 Page 1-16 of 18 Printed:29 May 2005, 06:31
Health and Safety lñÑçêÇ=fåëíêìãÉåíë=mä~ëã~=qÉÅÜåçäçÖó= mä~ëã~ä~Ä and fçåÑ~Ä
System vent gas: Nitrogen
Max inlet pressure : 5 Bar
WARNING
Warns of gas type and maximum pressure, connected to the system.
Gas type: Air (compressed)
Max inlet pressure : 9 Bar
WARNING
Warns of gas type and maximum pressure, connected to the system.
System process gas :
Max inlet pressure : 5 Bar
WARNING
Warns of gas type and maximum pressure, connected to the system.
Fluid type: Water (cooling)
Max inlet pressure : 4.2 Bar
WARNING
Warns of fluid type and maximum pressure, connected to the system
Caution, refer to accompanying documents. ISO 3864, No. B.3.1
Continued…
Health and Safety
Printed:29 May 2005, 06:31 Page 1-17 of 18 Issue 11: August 2004
mä~ëã~ä~Ä and fçåÑ~Ä lñÑçêÇ=fåëíêìãÉåíë=mä~ëã~=qÉÅÜåçäçÖó= Health and Safety
…Continued
On (Supply) IEC 417, No.5007
Off (Supply) IEC 417, No.5008
Earth (ground) IEC 417, No.5017
Protective earth (ground) IEC 417, No.5019
Three phase alternating Current IEC 617-2 No. 020206
3N
Three phase alternating Current with Neutral wire.
W
ARNING
HAZARDOUS
VOLTAGE
Disconnect electrical
supply before
removing cover
Warns of any voltage between 208V and 240V underneath the cover.
When used on its own, this label warns of any voltage between 208V
and 240V.
The labels below indicate the presence of high voltages within the labelled
equipment. There is a danger of electric shock or burns from touching
components within the labelled equipment.
DANGER
HAZARDOUS
VOLTAGE
415 Volts
50/60 hz
3 Phase
DANGER
HAZARDOUS
VOLTAGE
380 Volts
50/60 hz
3 Phase
DANGER
HAZARDOUS
VOLTAGE
208 Volts
50/60 hz
3 Phase
DANGER
HAZARDOUS
VOLTAGE
240 Volts
50/60 hz
DANGER
HAZARDOUS
VOLTAGE
220 Volts
50/60 hz
DANGER
HAZARDOUS
VOLTAGE
115 Volts
50/60 hz
Health and Safety
Issue 11: August 2004 Page 1-18 of 18 Printed:29 May 2005, 06:31