CP643E.pdf - 第6页
FK-9F98-05 CP- 643E Training Text for Service Engineers Edition 5.0 About this Manual Fuji Machine Mfg. Co., Ltd. Okazaki SMT Equipmen t Quality Assurance Dept. Technical Support Div. Section No.2 iii Page number A two d…
FK-9F98-05 CP-643E Training Text for Service Engineers
Edition 5.0 About this Manual
Fuji Machine Mfg. Co., Ltd. Okazaki
SMT Equipment Quality Assurance Dept.
Technical Support Div. Section No.2
ii
Page Layout
Each page indicates the chapter number and title, section number, body, manual name,
page number and edition number.
Chapter number
The chapter number to which each section belongs is shown in the header on each page.
The manual is made up of 12 chapters as detailed earlier in this section.
Section number and title
The title of each chapter is shown in the header on each page. Each part may contain one
or more sections.
Section title
Each chapter may be divided into several sections. The section number is composed of the
number of the chapter to which the section belongs, followed by a sequential number for
each section.
Body
The information needed to understand the workings of the machine and how to perform
adjustments is explained using text and illustrations.
Chapter number and title
Manual name
Manual reference number
FK-9F98-XX
Edition number
Edition 1.0
Page number
1-1
Chapter 1. Initial Setup
Fuji Machine Mfg. Co., Ltd.
Okazaki
SMT Quality Assurance Dept.
Technical Support Div. Section No.2
Manual created by
CP-7 Series Training text for Service Engineers
Section number
Body
1-
4
Recovery and Application Software Installation
1. Put the “Recovery CD” into the CD-ROM drive, which is at the
front of the M/C (center box). When installing the CD, the m/c
power must be on.
2. Press the “Windows” key on the keyboard connected to the
machine.
1) Select [Shut down] from the lower left menu.
2) Turn OFF the UPS when the following message appears:
“It is now safe to turn off your computer.”
3) Turn ON the UPS again.
4) Press [SYSTEM ON] from the machine operation panel.
3. Installation
1) When the previous operations are carried out, the display
will pause after the following message: “strike a key
when ready”. Press the space key on the keyboard three
times.
2) Installation will start. (It will take 3 to 5 minutes to
register.)
3) Once registering is finished, the following message will
show and pause:
“strike a key when ready”.
4) Press the space key and quickly change the recovery CD
to the application CD.
5)
FUJI Install software will start and the following message
FK-9F98-05 CP-643E Training Text for Service Engineers
Edition 5.0 About this Manual
Fuji Machine Mfg. Co., Ltd. Okazaki
SMT Equipment Quality Assurance Dept.
Technical Support Div. Section No.2
iii
Page number
A two digit hyphenated number appears in the footer on each page. The first digit of each page
number indicates the chapter number and the second digit is the sequential page number within that
chapter. Page 1-2, for example, indicates that this is the second page in the first chapter.
Manual name
The name of the manual that appears on the cover is also shown in the header on each page.
Edition number: The edition number is updated each time the manual is revised, with the number
reflecting the scale of changes that were made.
Minor revision: Minor changes are reflected in the part of the edition number after the decimal point,
for example, a change from edition 1.0 to 1.1. This change is made on the revised
pages only, and these pages can be downloaded as required from the Okazaki web
site.
Major revision: If major changes are made, the edition number is increased by one, for example, a
change from edition 1.0 to 2.0. This change is made on all pages, including the cover.
Purpose of this Training
• To provide knowledge and practical training in the areas of calibration and adjustment and
troubleshooting for the CP-643E machine.
• Carry out practical training for replacing and calibrating the various subsystems contained within
the machine.
• Give practical exercises on how to adjust, calibrate and maintain the subsystems to enhance the
overall efficiency of the machine.
Persons Qualified for This Training
Any agent level service engineers with experience in machine operation, maintenance will benefit from
the information contained in this manual.
This manual was primarily made for “Agent” level service engineers.
Any comments or opinions regarding this manual can be sent to trgall@okazaki.fuji.co.jp
CP-643 Series Training Text for Service Engineers
Version History:
FK-9F98-05 CP-643E Training Text for Service Engineers
Edition 5.0 About this Manual
Fuji Machine Mfg. Co., Ltd. Okazaki
SMT Equipment Quality Assurance Dept.
Technical Support Div. Section No.2
iv
Notes: