cp45ref.pdf - 第129页
Har dwar e T r oubleshooting 3-3 3.2.2.2. Detail Inspection for PC 3.2.2.2.1. VGA Card Check the LED in the lower right side of monitor . LED lit green: The m onitor is operating in normal. LED is blinking à The mo…
Samsung Component Placer CP-45F(V)/FS Reference Manual
3-2
3.2. Inspection of the Controller
3.2.1. Inspection of the Controller Part
The input power (AC 110V) of the power supply controller is supplied from the output
terminal of the Noise Filter 2 (NF#2) to the PS#1, PS#2-1, PS#2-2. The PS#1, PS#2-1,
PS#2-2 are attached to the Rear Side of the Control Rack. The PS#1 supply DC 5V and
PS#2-1 supply DC +12V and PS#2-2 supply DC -12V with VME Backplane and PC.
NF#2
PS#1
PS#2-1
PS#2-2
CDROM DRIVER
HDD
VGA CARD
PC ISA I/F CARD
Figure 3-2. Control Rack
3.2.2. Inspection of the Rack Part
3.2.2.1. Inspection for PC
① Check to see if the VGA card is installed properly.
② Check to see if the HDD cables are connected properly.
③ Check to see if the FDD cables are connected properly.
④ Check to see if the CD-ROM cables are connected properly.
⑤ Check to see if the PC ISA I/F boards are assembled properly.
Hardware Troubleshooting
3-3
3.2.2.2. Detail Inspection for PC
3.2.2.2.1. VGA Card
Check the LED in the lower right side of monitor.
LED lit green: The monitor is operating in normal.
LED is blinking
à The monitor is in power saving mode.
à Check to see if the monitor cable is connected properly.
à Check to see if the VGA card is installed properly.
LED is off
à Check to see if the power switch of the monitor is on.
à Check to see if the power supply cable is connected properly.
à Check to see if the power is being supplied.
à Check to see if the CP2 is cut off and the power is not supplied, if so turn
the power off and unplug the power cable, and then re-supply the power by
using the CP1.
Check to see if the VGA card is installed properly.
3.2.2.2.2. Hard Disk Drive (HDD)
Inspection for the power supply
Check the power supply referring to the below diagram.
Figure 3-3. Inspection for the power supply of HDD
Check to see if the HDD cable is connected properly.
Samsung Component Placer CP-45F(V)/FS Reference Manual
3-4
In case of the PC cannot detect the HDD
Check to see if the HDD is set as 'MASTER'.
JP4 □ □
JP3 □ □
JP2 □ □
JP1 □━□
Figure 3-4. HDD Jumper Setting
HDD detection
à First turn the power on, and then change to CMOS Setup mode by pressing
the <F2> or <Delete> key.
à Select the Standard CMOS Setup Menu from the main menu, and then
change the HDD type to 'AUTO' by using <Å>, <Æ>, <È>, <Ç> keys at
the Primary Master.
à Change to the main menu by pressing <Esc> key, and then enter into the
'IDE HDD auto detection'.
à Select the 'LBA' from the list.
à Change to the main menu by pressing <Esc> key, and then select the 'SAVE
& EXIT Setup' to store current setting.
à The PC may detect the HDD after automatic re-booting.
Booting using the FDD
Follow the below procedures in case of the 'IDE HDD auto detection' is not
available.
à Select the 'BIOS Features Setup' from the CMOS Setup main menu, and
then set the boot sequence as 'Boot Sequence: A, C' by using the <Pg Up>,
<Pg Dn> keys.
à Change to the main menu by pressing <Esc> key, and then select the 'SAVE
& EXIT Setup' to store current setting.
à Insert the Windows 98 startup disk into the FDD and then reboot.