cp45ref.pdf - 第61页

System Messages of the MMI and Solutions 2-7 $2002 Can't lower the BUT . [Problem] The BUT (Back Up T able) does not move when it is to be lowered. The down sensor is not sensed when the BU T (Back Up T able) is to …

100%1 / 149
Samsung Component Placer CP-45F(V)/FS Reference Manual
2-6
$1004 Error was detected at the $A axis.
[Problem]
An error occurred at the specified axis.
[Solution]
Check if there is any mechanical interference at the specified axis.
Check the specified axis and related wiring.
Replace the board of the specified axis.
$2000 Encoder error was detected at the conveyor width control axis.
[Problem]
An error occurred when the conveyor related encoder was checked.
[Solution]
Check the wiring related to conveyor width control.
Replace the related board.
$2001 Can 't raise the BUT.
[Problem]
The BUT (Back Up Table) does not move when it is to be lifted.
The up sensor is not sensed when the BUT (Back Up Table) is to be lifted.
The down sensor is sensed when the BUT (Back Up Table) is to be lifted.
[Solution]
Check if the air pressure supplied to the equipment is normal.
Check if the conveyor I/O board is normal.
Check the operation of the BUT up sensor.
Check the position of the BUT up sensor.
Check the operation of the BUT down sensor.
Check the position of the BUT down sensor.
System Messages of the MMI and Solutions
2-7
$2002 Can't lower the BUT.
[Problem]
The BUT (Back Up Table) does not move when it is to be lowered.
The down sensor is not sensed when the BUT (Back Up Table) is to be lowered.
The up sensor is sensed when the BUT (Back Up Table) is to be lowered.
[Solution]
Check if the air pressure supplied to the equipment is normal.
Check if the conveyor I/O board is normal.
Check the operation of the BUT down sensor.
Check the position of the BUT down sensor.
Check the operation of the BUT up sensor.
Check the position of the BUT up sensor.
$2101 Can 't move forward the edge fixer.
[Problem]
The edge fixer does not move when it is to be moved forward.
The move forward sensor is not sensed when the edge fixer is to be moved forward.
The move backward sensor is sensed when the edge fixer is to be moved forward.
[Solution]
Check if the air pressure supplied to the equipment is normal.
Check if the conveyor I/O board is normal.
Check the operation of the edge fixer forward sensor.
Check the position of the edge fixer forward sensor.
Check the operation of the edge fixer backward sensor.
Check the position of the edge fixer backward sensor.
Samsung Component Placer CP-45F(V)/FS Reference Manual
2-8
$2102 Can't move backward the edge fixer.
[Problem]
The edge fixer does not move when it is to be moved backward
The backward sensor is not sensed when the edge fixer is to be moved backward
The forward sensor is sensed when the edge fixer is to be moved backward
[Solution]
Check if the air pressure supplied to the equipment is normal.
Check if the conveyor I/O board is normal.
Check the operation of the edge fixer backward sensor.
Check the position of the edge fixer backward sensor.
Check the operation of the edge fixer forward sensor.
Check the position of the edge fixer forward sensor.
$2201 HOLE_FIX_UP_ERROR.
$2202 HOLE_FIX_DOWN_ERROR.
$2210 The sensor of the hole fixer is not sensed.
[Problem]
When a PCB is to be fixed by the hole fix method, the sensor is not sensed.
[Solution]
Check the position of the hole fixer.
Check the wiring related to the hole fixer.
$2211 The right sensor of the hole fixer is not sensed.
[Problem]
When a PCB is to be fixed by the hole fix method, the right sensor is not sensed.
[Solution]
Check the position of the right hole fixer.
Check the wiring related to the right hole fixer.