cp45ref.pdf - 第65页
System Messages of the MMI and Solutions 2-1 1 [Problem] 1. A PCB is in the mounting sensor area when the operation is to start [Solution] If there is one PCB in the conveyor mounting and if it is all right to start oper…
Samsung Component Placer CP-45F(V)/FS Reference Manual
2-10
Check the operation of the edge fixer forward sensor.
Check the position of the edge fixer forward sensor.
$2400 Error occurred when the conveyor width was adjusted
[Problem]
An error occurred when the conveyor width was adjusted.
[Solution]
Replace the board related to the adjustment of conveyor width.
$3000 PCB is in the conveyor area.
[Problem]
A PCB is on the conveyor when the conveyor width is to be adjusted
[Solution]
Remove the PCB from the conveyor.
Check if the XY is sensed by the sensor on the conveyor.
$3001 PCB is in the input sensor area.
[Problem]
A PCB is in the input sensor area when the operation is to start.
[Solution]
If there is one PCB in the conveyor input , press START.
If there is more than one PCB in the conveyor input , remove them.
$3002 PCB is in the waiting sensor area.
[Problem]
A PCB is in the waiting sensor area when the operation is to start.
[Solution]
If there is one PCB in the conveyor input , press START.
If there is more than one PCB in the conveyor input , remove them.
$3003 PCB is in the mounting sensor area.
System Messages of the MMI and Solutions
2-11
[Problem]
1. A PCB is in the mounting sensor area when the operation is to start
[Solution]
If there is one PCB in the conveyor mounting and if it is all right to start operation,
press START.
If there is more than one PCB, remove them.
$3004 PCB is in the output sensor area.
[Problem]
A PCB is in the output sensor area when the operation is to start
[Solution]
If there is one PCB in the conveyor output and if it is all right to start operation,
press START.
If there is more than one PCB in the conveyor output , remove them.
$3010 There are two PCBs in the input buffer.
[Problem]
This error occurs when the input sensor and waiting sensor are sensed simultaneously
[Solution]
If the PCB size is such that it can be sensed simultaneously, check the PCB size in the
Board of PCB Edit.
Check the sensitivity of the sensors.
$3021 PCB is in the input buffer or waiting buffer.
[Problem]
A PCB is in the input terminal sensor area when the operation is to start.
[Solution]
If there are more than one PCB in the conveyor input terminal, remove them.
$3022 PCB is in the mounting buffer.
[Problem]
Samsung Component Placer CP-45F(V)/FS Reference Manual
2-12
A PCB is in the mounting sensor area when the operation is to start.
[Solution]
If there is one PCB in the conveyor mounting terminal and if it is all right to start
operation, press START.
If there is more than one PCB in the conveyor mounting terminal, remove them.
$3023 PCB is in the output buffer.
[Problem]
A PCB is in the output sensor area when the operation is to start
[Solution]
If there is one PCB in the conveyor output terminal and if it is all right to start operation,
press START.
If there is more than one PCB in the conveyor output terminal, remove them.
$3101 PCB has not arrived in the waiting sensor area.
[Problem]
The PCB is dropped during transfer
The PCB is blocked due to mechanical interference during transfer
The sensitivity of the waiting sensor is adjusted incorrectly
The time out value is too low.
[Solution]
Remove the dropped PCB and start again.
Remove the mechanical interference.
Adjust the sensitivity of the waiting sensor again.
Adjust the time out value. (Factory setting)
$3102 PCB has not arrived in the mounting sensor area.
[Problem]
The PCB is dropped during transfer
The PCB is blocked due to mechanical interference during transfer