cp45ref.pdf - 第23页
T able of Cont ents xvxv Figure 0-2. Safety labels attached o n the rear part of the machine ...................... v Figure 0-3. Safety labels attached o n the internal part of the machine ................. v Figure 1-1…
Samsung Component Placer CP-45F(V)/FS Reference Manual
xiv
1.2.3.9. Conveyor Cylinder Operation..................................................... 1-5
1.2.4.
Electric Device.................................................................................1-5
1.2.5. Feeder Station Section ....................................................................1-5
1.2.5.1.
Feeder Base...............................................................................1-5
1.2.5.2. Adjustment of Multi Cylinder Speed........................................... 1-5
1.2.6.
Upward Vision Unit ..........................................................................1-5
1.2.6.1.
Cover Glass ............................................................................... 1-5
1.2.6.2. Camera Lens.............................................................................. 1-5
1.2.7.
Pneumatics......................................................................................1-5
1.2.7.1.
Pressure Settings.......................................................................1-5
1.2.7.2. Air Filter & Auto Drainer ............................................................. 1-5
1.2.7.3. Gauge and Pressure Switch ...................................................... 1-5
1.2.7.4. Connections and Fittings............................................................1-5
1.2.8.
Component Feeding Sub-Systems (Feeders)..................................1-5
1.3. Noise Solution................................................................................ 1-5
Troubleshooting Guide
Chapter 2. System Messages of the MMI and Solutions.................................. 2-5
Chapter 3. Hardware Troubleshooting ............................................................. 3-5
3.1. Power Inspection............................................................................ 3-5
3.2. Inspection of the Controller............................................................. 3-5
3.2.1. Inspection of the Controller Part ......................................................3-5
3.2.2. Inspection of the Rack Part..............................................................3-5
3.2.2.1.
Inspection for PC........................................................................3-5
3.2.2.2. Detail Inspection for PC .............................................................3-5
3.2.2.3. Inspection of the Machine Controller..........................................3-5
3.3. Inspection of the Motor Part ........................................................... 3-5
3.3.1. X-axis...............................................................................................3-5
3.3.2. Y-axis...............................................................................................3-5
3.3.3. Z1~Z6, S, W axis .............................................................................3-5
3.3.4. R1/2, R3/4, R5/6 axis(THETA1, THETA2, THETA3)....................... 3-5
3.4. MVME162-220 Jumper Setting ...................................................... 3-5
3.5. AC Servo Driver Digital Switch Setting........................................... 3-5
3.6. R-Axis Step Motor Driver Digital Switch Setting............................. 3-5
3.7. Conveyor Step Motor Driver Digital Switch Setting ........................ 3-5
3.8. Motor troubleshooting..................................................................... 3-5
3.9. Sensors on the Machine................................................................. 3-5
3.9.1. The Sensor Lay-Out......................................................................... 3-5
3.9.2. The Sensor Part List........................................................................3-5
Technical Drawings & Electric Schematics
List of Figures
Figure 0-1. Safety labels attached on the front part of the machine......................v
Table of Contents
xvxv
Figure 0-2. Safety labels attached on the rear part of the machine ......................v
Figure 0-3. Safety labels attached on the internal part of the machine.................v
Figure 1-1. Flying vision.....................................................................................1-5
Figure 1-2. nozzle holder ...................................................................................1-5
Figure 1-3. Vacuum Filter Inspection..................................................................1-5
Figure 1-4. Replacing the filter...........................................................................1-5
Figure 1-5. Remove the contamination in the spline shaft.................................1-5
Figure 1-6. Vacuum Generator...........................................................................1-5
Figure 1-7. X-axis L/M Guide Rail & Block.........................................................1-5
Figure 1-8. Y-axis L/M Guide..............................................................................1-5
Figure 1-9. Y axis ball screw grease nipple........................................................1-5
Figure 1-10. PCB Conveyor Belt........................................................................1-5
Figure 1-11. Lead Screw for Adjusting Conveyor Width.....................................1-5
Figure 1-12. PCB Detect Sensor........................................................................1-5
Figure 1-13. Conveyor Speed Control Volume...................................................1-5
Figure 1-14. Stopper Inspection Points..............................................................1-5
Figure 1-15. Speed Control Valves ....................................................................1-5
Figure 1-16. Upward Vision Unit ........................................................................1-5
Figure 1-17. Inspection for Pneumatics .............................................................1-5
Figure 3-1. Power Inspection.............................................................................3-5
Figure 3-2. Control Rack....................................................................................3-5
Figure 3-3. Inspection for the power supply of HDD..........................................3-5
Figure 3-4. HDD Jumper Setting........................................................................3-5
Figure 3-5. FDD, MOUSE, KEYBOARD............................................................3-5
Figure 3-6. Inspection for the power supply of FDD...........................................3-5
Figure 3-7. Inspection for the power supply of CD-ROM...................................3-5
Figure 3-8. MVME162-220 Jumper Setting........................................................3-5
Figure 3-9. XY, H1/2 Axis Board Jumper Setting................................................3-5
Figure 3-10. H3/4, H5/6 Axis Board Jumper Setting ..........................................3-5
Figure 3-11. CAN MASRTER Board Jumper Setting.........................................3-5
Figure 3-12. STEP I/F Board Jumper Setting.....................................................3-5
Figure 3-13. AC Servo Driver Digital Switch Setting ..........................................3-5
Figure 3-14. R-Axis Step Motor Driver Digital Switch Setting.............................3-5
Figure 3-15. Conveyor Step Motor Driver Digital Switch Setting........................3-5
Figure 3-16. The locations of sensors on the machine ......................................3-5
List of Tables
Table 1-1. Table of Preventive Maintenance List................................................1-5
Table 1-2. Replacement period list.....................................................................1-5
Table 1-3. Table of Component Lubrication........................................................1-5
Table 3-1. Motor Troubleshooting.......................................................................3-5
Table 3-2. The table of sensor part list...............................................................3-5