创建组件识别数据的方法.pdf - 第69页

69/178 IM-SMT-VSNDI C-0002 -000 Items to be set Set value Cntr . Offset R (m m) 0.0 Ruler Offset E 5 Ruler W idth 3 Lead Num ber E 14 Lead Pitch (m m) 1.0 Lead W idth (mm) 0.3 Reflect LL. (m m) 1.0 Table 46 Figure 54 2.9…

100%1 / 178
68/178
IM-SMT-VSNDIC-0002-000
This mode is used for the connector components that have leads only in one direction.
Figure 53
[Recognition check items]
Items Yes / No Notes
Body Size No
Lead pitch Yes The pitch in the direction with one lead is not checked.
Lead width May exist
Checks only when the lead width is more than 1.0mm.
(Note 1)
Reflect LL No
Find Pos No
Table 45
Note:
“Lead width” check function may not be available for some old software versions.
The following is the actual example of the setting and the recognition result.
<< Items to be set for single-direction connectors>>
Items to be set Set value
Alignment Group Connector
Alignment Type Con- E
Comp. Threshold 50
Comp. Tolerance 30
Search Area (mm) 5.0
Body Size X (mm) 6.0
Body Size Y (mm) 15.0
Body Size Z (mm) 2.0
Cntr. Offset X (mm) 0.0
Cntr. Offset Y (mm) 0.0
Lead length
Lead width
Lead pitch
Bod
y Size Y
Body Size X
69/178
IM-SMT-VSNDIC-0002-000
Items to be set Set value
Cntr. Offset R (mm) 0.0
Ruler Offset E 5
Ruler Width 3
Lead Number E 14
Lead Pitch (mm) 1.0
Lead Width (mm) 0.3
Reflect LL. (mm) 1.0
Table 46
Figure 54
2.9.2. 4-direction connectors
<< Items to be set for 4-direction connectors>>
Items to be set Set value Explanation
Alignment Group Connector
Sets the component category.
Alignment Type Con-NSEW
Sets the component type.
Comp. Threshold
Sets the detection level difference for
lead detection
. (See “Appendix 2. Detection
level differences used to detect leads
(threshold value)”.)
Comp. Tolerance
Specifies the tolerance of the lead pitch
as a percentage.
Search Area (mm) Sets the range of the detection.
70/178
IM-SMT-VSNDIC-0002-000
Items to be set Set value Explanation
Body Size X (mm) Sets the size of the outer edge.
Body Size Y (mm) Sets the size of the outer edge.
Body Size Z (mm) Sets the size of the outer edge.
Cntr. Offset X (mm)
Sets the offset amount in the X direction
from the center position.
Cntr. Offset Y (mm)
Sets the offset amount in the Y direction
from the center position.
Cntr. Offset R (mm)
Sets the offset amount of the angle of
rotation.
Ruler Offset N
Sets the offset amount for the detection
line in the N direction.
Ruler Offset S
Sets the offset amount for the detection
line in the S direction.
Ruler Offset E
Sets the offset amount for the detection
line in the E direction.
Ruler Offset W
Sets the offset amount for the detection
line in the W direction.
Ruler Width
Lead Number N
Sets the number of leads in the N
direction.
Lead Pitch N (mm) Sets the lead pitch in the N direction.
Lead Width N (mm) Sets the lead width in the N direction.
Reflect LL. N (mm)
Sets the lead length on the image in the
N direction.
Lead Number S
Sets the number of leads in the S
direction.
Lead Pitch S (mm) Sets the lead pitch in the S direction.
Lead Width S (mm) Sets the lead width in the S direction.
Reflect LL. S (mm)
Sets the lead length on the image in the
S direction.
Lead Number E
Sets the number of leads in the E
direction.
Lead Pitch E (mm) Sets the lead pitch in the E direction.
Lead Width E (mm) Sets the lead width in the E direction.
Reflect LL. E (mm)
Sets the lead length on the image in the
E direction.
Lead Number W
Sets the number of leads in the W
direction.
Lead Pitch W (mm) Sets the lead pitch in the W direction.
Lead Width W (mm) Sets the lead width in the W direction.
Reflect LL. W (mm)
Sets the lead length on the image in the
W direction.
Table 47
This mode can be used for recognition of not only four directions but also one direction, two
directions and three directions.
The data should be set for only the necessary direction(s), and data for directions that are
not necessary should be set to 0.
Leads in the N/S direction must be symmetrical on the left and right sides, and leads in
the W/E direction must be symmetrical on the upper and lower sides. This is because the
reference lead position is determined from the center of the outer edge, based on the Lead
Number and the Lead Pitch.