ALFeeder_E.pdf - 第11页

2. Safety S-4 Introduction 2.3 Keeping body and objects away fr om moving parts During use of a mounter , a customer’ s equipment and operating conditions might allow the operator’ s body (including parts of y our bod y …

2. Safety

S-3

Introduction

2.2 Safety message

█

Safety message: The following describes precautionary items.

TIP

Provides helpful explanation for work.

NOTE

Provides required information when operating the machine in a simple and clear manner.

CAUTION

Indicates a potentially hazardous situation which, if not avoided, may result in minor injury, or material loss or damage to

the machine. These points are important for protecting the safety of the machine and data, etc.

WARNING

INDICATES A POTENTIALLY HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, COULD RESULT IN DEATH OR SERIOUS

INJURY. THESE ARE POINTS MOST ESSENTIAL FOR PROTECTING THE SAFETY OF THE MACHINE OPERATOR, INSPECTOR

AND SERVICE PERSONNEL.

If this mark is in this manual, make sure to work while a machine is ins emergency stop.

█

Warning label: Power station for offline setup and other equipment

To use this equipment safely and correctly, warning labels are attached to the equipment. Make sure to

understand the description of warning label and comply with the instructions.

Potential hazard

If the equipment is not connected to the power source with the specified voltage, it may

result in the breakage or malfunction of the equipment.

To avoid hazard

Make sure to connect the equipment to the power source with the specified voltage

referring to the manual.

Case Setup

Label position Serial number label area

Label positions

Feeder external equipment

Power unit for carriage

Power station for offline setup

Tune-up station

63009-KLU-30

2. Safety

S-4

Introduction

2.3 Keeping body and objects away from moving parts

During use of a mounter, a customer’s equipment and operating conditions might allow the operator’s

body (including parts of your body and clothing) and other objects to come into contact with moving parts.

Use the following safety measure options to avoid possible danger where openings or gaps are found on the

mounter.

█

Dummy feeder

Use dummy feeders as safety measures to fill a gap between feeders, to prevent your hand or body part

from inserting into it.

When the reel switching operation executed by Auto Loading Feeder, a component tape may be

protruded forcibly. If the tape ejection path (slope) is stucked by the cause of as such the remained

carriar tapes in the Dust Box, it may cause the protruding of the long carriar tape ejected forcibly into

machine from the empty slot beside of feeders.

This may cause some pickup error or machine trouble, filling the empty feeder slots using dummy

feeders is recommended around Auto Loading Feeder.

Moreover, instead of dummy feeders, the feeders described below can be used; SS feeder, ZS feeder or

Auto Loading Feeder.

Part name Part number Remarks

Dummy feeder KLJ-M34D0-01X New model

NOTE

Though the former model of dummy feeders (KLJ-M34D0-00X) is also provided, apply a dummy feeder described above to

ﬁll the empty slots besides of Auto Loading Feeder.

█

One-stop cover

If not using a feeder exchange carriage for a mounter that is to be used with feeder exchange carriages

(excluding YSM40R), attach an one-stop cover to the position where a feeder exchange carriage is

attached to prevent body and objects from entering.

Prevention of body and objects entry

Dummy feeder and One-stop cover

Dummy feeder (8 mm size)

One-stop cover

63002-KLU-30

CAUTION

Do not apply strong impact to the one-stop cover for YRM20, as it contains a board within.

NOTE

One-stop cover cannot be attached/detached during operation. The mounter must be in a stopped state because the

section where a feeder exchange carriage is to be installed will move up and down for attaching or detaching the feeder

exchange carriage.

Chapter 1 Overview

Contents

1. Overview 1-1

1.1 Part names and functions 1-1

1.2 Handling precautions 1-4

1.3 Types of Auto loading feeder and available component size 1-8

1.4 Selecting Auto loading feeder with special jig 1-9

1.4.1

Cover tape checker (for checking the seal of cover tape and pocket size)

1-9

1.4.2 Tape cut jig / Tape leveler 1-10

1.5 Available component tape and limitation items 1-11

1.5.1 Limitation items 1-11

1.5.2 Detail of available component tape 1-13

1.5.3 Standard for component tape 1-16