ALFeeder_E.pdf - 第88页

Chapt er 4 Maintenanc e and par t s replacement Contents 1. Maintenance 4-1 1. 1 Maintenance sections/Replaceable par ts 4- 1 2. Preparation f or maintenance 4-2 2.1 Requir ed to ols 4-2 2.2 Maintenance sections 4-2 2.3 …

100%1 / 112
4. Troubleshooting
3-41
Chapter 3 Setting up
4.6 Feeder Guide type is incorrect.
█
Error : Feeder does not operate as error message "AL feeder guide size mismatch error"
is displayed.
►
Cause
Request type of tape guide on board data and actual type of tape guide attached to Auto loading
feeder are different.
►
Countermeasure
Check the attached component and the type of tape guide to be used (2S/S/M/L/LL). Then replace the
feeder with one that type is same as request type of tape guide .
LED1
LED2
LED3
FEED
BACK
FUNC
LOAD
Feeder Guide type is incorrect.
Tape guide type is not same as feeder type
Types are different.
Cause of error
Tape guide type (M)
Request type of tape guide type (S)
64307-KLU-30
Chapter 4 Maintenance and parts
replacement
Contents
1. Maintenance 4-1
1.1 Maintenance sections/Replaceable parts 4-1
2. Preparation for maintenance 4-2
2.1 Required tools 4-2
2.2 Maintenance sections 4-2
2.3 Replaceable parts 4-3
3. Maintenance / Replacing procedure 4-5
3.1 Tape guide 4-5
3.1.1 Cleaning 4-5
3.1.2 Replacing tape guide assembly 4-7
3.2 Maintaining tape guide assembly 4-8
3.2.1 Cleaning tape path/Replacing leaf spring 4-8
3.2.2 Replacing pusher assembly 4-9
3.2.3 Replacing discharge assembly 4-9
3.3 Front block 4-10
3.3.1 Replacing front block 4-10
3.4 Connecting section for feeder bank 4-11
3.4.1 Replacing under rail 4-11
3.4.2 Replacing reel holder bracket 4-11
3.5 Clamp section 4-12
3.5.1 Replacing clamp lever assembly 4-12
3.5.2 Replacing tail pin 4-13
3.6 Electrical connecting section 4-14
3.6.1 Replacing board connector 4-14
3.7 Operation section 4-15
3.7.1 Replacing handle 4-15
3.8 Loading unit 4-16
3.8.1 Replacing clamp units 4-16
3.9 Preset holder section 4-17
3.9.1 Replacing sliding stopper 4-17
1. Maintenance
4-1
Chapter 4 Maintenance and parts replacement
1. Maintenance
This section describes the inspection, cleaning, and replacing parts to operate Auto loading feeder in
good condition. Make sure to maintain Auto loading feeder periodically.
c
CAUTION
Only trained personnel should perform maintenance of Auto loading feeder, both carefully and in accordance with the
procedures specified.
1.1 Maintenance sections/Replaceable parts
Maintenance sections/Replaceable parts
3.1 Tape guide
3.2 Tape guide section
3.7 Operation section
3.3 Front block
3.5 Clamp section
3.6 Electrical
connecting section
3.8 Loading unit
3.4 Connecting section
for feeder bank
3.4 Connecting section
for feeder bank
Clamp unit
Under rail
Reel holder bracket
Clamp lever assembly
Cleaning
Lubricating
Replacing
Leaf spring/Pusher/Discharge assembly
Tape guide assembly
Handle
Board connector
3.9 Preset holder section
Sliding stopper
Front block
Tail pin
* Jumps to target page by clicking from 3.1 to 3.9.
Click to return to this page.
63401-KLU-50