3OM-996-005.pdf - 第215页
3 .3 "Recognition Data" T ab • Sheet Layout When the "Recognition Data" tab is pressed, the "Recognition Data" tab sheet appears. The "Recognition Data" tab sheet can be classified…
(3) Component Shape: Other Leaded (Complex)
*1 Type
Different items will be displayed in "*5", depending on which
type is selected in this text box.
Standard
"Shape", "Width [mm]" and "Length [mm]" appear in "*5".
Electd
"Shape", "Width [mm]", and "Full Length [mm]" appear in "*5".
Others
"Width [mm]", "Length [mm]", and "Full Length [mm]" appear
in "*5".
*2 # Of types, *3 # Of groups
*4 Extended setting
Different items will be displayed in "*6", depending on which
parameter ("Disable" or "Enable") is set in this text box.
Disable
"Type No.", "Direction [deg]", "# of Leads [pcs.]", "Pitch [mm]",
"Center Posn (Latl Dir) [mm]", and "Top Posn (Long Dir) [mm]"
appear in "*6".
Enable
"Type No.", "Direction [deg]", "# of Leads [pcs.]", "Pitch [mm]",
"Center Posn (Latl Dir) [mm]", "Top Posn (Long Dir) [mm]",
"Missing Lead Start", "# of Missing Leads [pcs.]", and "Insp
Condtn" appear in "*6".
*5 Lead Type Data
Shape, Width [mm], Length [mm], Full Length [mm]
*6 Lead Group Data
Type No., Direction [deg], # of Leads [pcs.], Pitch [mm], Cen-
ter Posn (Latl Dir) [mm], Top Posn (Long Dir) [mm], Missing
Lead Start, # of Missing Leads [pcs.], Insp Codtn
0510-002 3-27
AIM01EDTP
3.2 "Shape Data" Tab
3.3 "Recognition Data" Tab
• Sheet Layout
When the "Recognition Data" tab is pressed, the "Recognition Data"
tab sheet appears.
The "Recognition Data" tab sheet can be classified by shapes and
divided into two kinds as follows.
• Cylindrical, Square, Deform (Simple)
• IC (Simple), Other Leaded (Simple), Connector (Simple)
3.3.1 Cylindrical, Square, and Deform (Simple)
Fig. 3C18 "Recognition Data" Tab Sheet ("Square" Selected)
• Sheet Composition
Each parameter is displayed or can be entered.
Refer to "4.1.3 Basic Usage of Text Boxes" (Section 2) for the
detailed information on how to enter each parameter.
*1 Lighting mode, *2 Recog data set, *3 Recog level,
*4 Back ltg algo (Front ltg algo), *6 View range Set
"Back ltg algo" or "Front ltg algo" appears in "*4", depending on
which lighting mode is selected in the "Lighting mode" text box.
3.3 "Recognition Data" Tab
*1
*2
*3
*4
*5
*6
*7
0510-002 3-28 AIM01EDTP
Note
Note
*5 Lighting pattern
Back ltg, Front ltg 1 (Ring), Front ltg 2 (Coax)
When "Manual" is set in the "Lighting pattern" text box, it is re-
quired to enter parameters in these text boxes.
*7 Mold size tol Set
Mold size tolerance X [mm] (Horizontal), Mold size toler-
ance Y [mm] (Vertical)
When "Manual" is set in the "Mold size tol Set" text box, it is re-
quired to enter parameters in these text boxes.
Fig. 3C19
*8 Upper/Lower surface detn
When the "Front Ltg System" is set in the "Lighting system" text
box (*1), it is required to enter a parameter in the text box.
Cmpnt-Mounted surf image
When "Enable" is set in the "Upper/Lower surface detn", it is re-
quired to enter a parameter in the text box.
When a component shape other than "Square" is selected
in the "Component shape" combo box, "Upper/Lower sur-
face detn" is not displayed.
The upper/lower surface detection function can be used
when the component shape is "Square" and the pickup
surface appears black.
0510-002 3-29
AIM01EDTP
3.3 "Recognition Data" Tab
*6
*7
*8
Note