OperationInstruction_Vsision XP.pdf - 第210页
Page 202 V ISION XP+ V AC Page List of T ables Operating Instructions V ersion 1.5
Page 202 VISION XP+ VAC
Page
List of Tables
Operating Instructions
Version 1.5
VISION XP+ VAC Page 203
Index
Operating Instructions
Version 1.5
Index
Symbols
"Up" button.....................................................170
A
Activate trigger...............................................161
Active cooling module (option).........................65
Additional Heat Zone Monitoring......................78
Administrator....................................................13
Alarm
– Condensate Trap Error (VXP) ....................183
– Conveyor Adjustment Current ....................195
– Conveyor Drive Current..............................195
– Cooling section open (VXP) .......................181
– Cooling section volume flow malfunction ...188
– Cooling system failure................................191
– Cooling Tract Circulation ............................184
– Cooling Water failure (option).....................189
– Drive Motor.................................................183
– Dropped Board Monitoring OK (option)......195
– Emergency-Stop Activated.........................178
– Error Circuit ................................................188
– Exhaust ......................................................181
– Fan Monitoring ...........................................181
– Filling level chain oiler is too low (option) ...194
– Flow Monitoring Residue Management......194
– Frequency Converter..................................180
– Heating Element Monitoring, Power Controller
187
– Heating Elements Fault ..............................182
– Max. Temp. Limit Value Exceeded.............186
– Max. Temperature Tolerance Exceeded ....186
– Min. Temp. Tolerance Fallen Short Of .......186
– Motor Overload Protection Tripped ............179
– N2 consumption OK / too high ...................191
– N2/O2 Pressure Too Low...........................191
– O² tolerance warning..................................192
– O2 Tolerance injury ....................................192
– Outlet Interface (Option-Siemens-Interface) ....
188
– Overtemperature Protection Tripped..........183
– PCB accumulation inlet ..............................188
– PCB Feed Monitoring.................................187
– PCB length (vacuum process)) ..................193
– PCB Transfer..............................................187
– Phase Monitoring Tripped ..........................179
– PLC Communication ..................................194
– PLC Field Modules .....................................194
– Power Supply .............................................184
– Process Chamber Open.............................182
– Residual Oxygen Meter Malfunction ..........192
– Sensor fault ............................................... 193
– Speed ........................................................ 185
– Standstill Monitoring .................................. 185
– The oven is locked by MES ....................... 196
– Transport adjustment OK / failure.............. 195
– Vacuum process OK.................................. 193
– Vacuum pumpe OK ................................... 193
– Water amount is too low (option)............... 190
– Water Leak (option) ................................... 190
Alarm Messages ................................... 105, 177
Attaching Warning Signs................................. 25
Auto-Start-Switch ............................................ 24
B
Barcode Carriercode ..................................... 128
Before Initial Start-Up...................................... 38
Bushing Chain Conveyor ................................ 50
C
Calculate gradient ......................................... 167
CCS Retro-Reflective Sensor ......................... 53
Center Support (CS) ....................................... 54
Chain Lubricator............................................ 114
Chain Tensioners / Center Board Support ...... 51
Chain Tensioners / Transport Chain ............... 51
Change settings ............................................ 174
Changing a Password ..................................... 91
Chart ............................................................. 163
Checkbox ...................................................... 165
Close chart legend ........................................ 167
Company Address............................................. 3
Condensate Trap ............................................ 68
Condensate trap VXP ..................................... 68
Connection Locations...................................... 34
Connections .................................................... 34
Connections of the nitrogen regulation ........... 72
Consumption Display .................................... 131
Contact Address................................................ 3
Control Cabinet, Section 1 .............................. 74
Control Cabinet, Section 2 .............................. 75
Control Cabinet, Section 3 .............................. 76
Control Cabinet, Section 4 .............................. 76
Control Cabinets ............................................. 74
Conveyor
– Values........................................................ 112
Conveyor Speed Monitoring............................ 52
Conveyor System............................................ 48
Conveyor types ............................................... 48
Cooling System ............................................... 70
Cooling Tract................................................... 61