CP-7-series Verification System Instruction manual(2.0E).pdf - 第22页
4. Adjustments Edition 2.0 11 CP-7-series V erification System Instruction Manual (10) Remove the jig, then place feeders with 2D codes at the first and last slots of each stage (slot Nos. 1 and 30, or 1 and 40 on the CP…
4. Adjustments
Edition 2.0 10 CP-7-series Verification System Instruction Manual
(2) With a “Scene 1” status established, press the [→] key at the console to move to the
mode item, then set the [System] content as shown in Table 1.
(3) After setting all the [System] items, move to the [Save] item to save the data.
(4) Proceed to the [Measure] item.
(5) At the machine’s touch-screen, select [Maintenance] - [Configuration]
- [Machine Function Settings] - [Part Administration System] - [Use FujiTrax Verifier],
then select [Fujitrax Verifier Settings], and select [2D code camera] at the “Feeder ID
reading system” item.
(6) Set a jig in slot 1 of Stage 1, then move to the pick-up position.
(7) Select [Maintenance] - [Maintenance for Each Machine] - [Feeder Check Reader Test]
- [Feeder ID Reading] to display a broken line on the monitor. As the “Through” screen
mode (real image) is in effect at this time, adjust the camera height until the jig is in
focus.
(8) Adjust the camera in the XY-directions to align the broken line center with the center of
the square label on the jig (the gap between the broken line frame and the label sides
should be uniform as shown below).
(9) Restart the machine and verify that no errors occur.
Scent 0
Measurement
Scent 0
Measurement
Gap
Gap should be uniform on all sides
Jig label
Monitor’s broken line display
Gap
CP7V0089E
4. Adjustments
Edition 2.0 11 CP-7-series Verification System Instruction Manual
(10) Remove the jig, then place feeders with 2D codes at the first and last slots of each stage
(slot Nos. 1 and 30, or 1 and 40 on the CP-742ME, 1 and 70 on the CP-742E). With the
feeders set in position, select [Maintenance] - [Maintenance for Each Machine]
- [Feeder Check Reader Test] - [Feeder ID Reading], verifying that the IDs are read
correctly.
If reading occurs correctly, the green LEDs light at the slots where the feeders are set,
and “OK” displays at the upper right of the rear monitor, as shown in the figure below.
When 2D code reading does not occur correctly:
1. Check to see if the feeder’s label is peeled off, or is in the wrong position.
2. Move the error feeder to the pick-up position, display the “Through” mode screen (using
the same command as in Step 7 above), then check to see if the 2D code image is clearly
focused.
3. Adjust the camera position, and verify that the calibration data (D-axis pick-up position) is
correct.
Search area
OK
CP7V0090E
Scent 0
Measurement
4. Adjustments
Edition 2.0 12 CP-7-series Verification System Instruction Manual
2. Adjustment Procedure For Barcode Reader
(1) Select the “Barcode reader” Setting
Begin by moving Stage 1 to its standby position.
At the machine’s touch-screen, select [Maintenance] - [Configuration]
- [Machine Function Settings] - [Part Administration System] - [Use FujiTrax Verifier],
then select [Fujitrax Verifier Settings], and select [Barcode reader] at the “Feeder ID
reading system” item.
(2) Mount the barcode reader position adjustment jig.
Set the barcode reader positioning jig in slot 1 of Stage 1, then select [Maintenance]
- [Maintenance for Each Machine] - [Feeder Check Reader Test] - [Feeder ID Reading] at
the control panel.
Z9726DCPJ1702
Z9726DCPJ1712
Z9528DHPJ2680
DCPJ0340
AWCC4602
Set jig in slot 1 of Stage 1
Jig
Stage 1
Positioning label 1
Positioning label 2
CP7V0091E
Feeder ID barcode reader position
adjustment jig components
Rear operation monitor
Barcode reader
mounting position
Device pallets
CP7V0093E
Acrylic cover