CP43操作手册.pdf.pdf - 第239页
Chapter 1 Proper Data Listing Part 4 # 1: ID_Code [8] ASCII CODE = 0 # 2: Language = [English] Japanese French # 3: Red_Light = 0000 0000 0000 0000 # 4: Y ellow_Light = 0000 0000 0000 0000 # 5: Blue_Light = 0000 0000 000…
Part Four
Proper Data
Chapter 1 Proper Data ListingPart 4
# 1: ID_Code [8] ASCII CODE = 0
# 2: Language = [English] Japanese French
# 3: Red_Light = 0000 0000 0000 0000
# 4: Yellow_Light = 0000 0000 0000 0000
# 5: Blue_Light = 0000 0000 0000 0000
# 6: Red_Flash = 0000 0000 0000 0000
# 7: Yellow_Flash = 0000 0000 0000 0000
# 8: Blue_Flash = 0000 0000 0000 0000
$# 9: User_Define A = 0000 0000 0000 0000
❈ 11: Machine_Status A = 0000 0000 0000 0000
❈ 12: Machine_Status B = 0000 0000 0000 0000
❈ 13: Machine_ID = 0000 0000 0000 0000
# 14: PCB_Location = [Corner] Pin
$ 20: Loader Status A = 0000 0000 0000 0000
$ 21: Loader Status B = 0000 0000 0000 0000
$ 22: Conveyor Type = [L->R] R->L
$ 23: Wait Signal = [Off] On
$# 24: Busy Invalid = [No] Yes
$# 25: Conveyor Control = [Manu] Auto
$# 26: Conveyor Adj. Limit ( 0.05 ~ 1.00 ) [mm] = 0.50
$# 27: Conveyor Stop Offset ( 0.00 ~ 2.00 ) [mm] = 0.30
$# 28: Conveyor adj. Timer ( 0 ~ 120000 ) [msec]= 000600
$❈ 29: Width Max Limit ( 0.00 ~ 655.35 ) [mm] = 460.00
4 – 1Version 2.0
DATA NAME
1. Proper Data Listing
The following symbols are used before the Proper data values.
✩: Varies from machine to machine. Must be measured.
❈: Cannot be changed by the user.
#: Can be changed by the user.
@: Machine automatically changes this. (Sometimes the user can also
change this.
$: Not currently in use.
$❈ 30: Width Min Limit ( 0.00 ~ 655.35 ) [mm] = 050.00
$# 40: LMS Flag = [Off] On
$# 41: Cell Status = [Unit] Active Passive
$# 42: Change Over Mode ( 0 ~ 200 ) = 000
$# 43: Auto Start = [No] Yes
$# 44: Backup Plate Check = [No] Yes
$❈ 45: Command Line Status = [RS232C] LAN ETHERNET
$# 46: Command Line Port ( 0 ~ 4 ) = 0
$✳ 47: ID Station Type = [S_type] A_type
$# 48: Buzzer Warning = [On] Off
$# 49: Process Timer ( 1 ~ 120000 ) [msec]= 010000
$# 50: Reader Type ( 0 ~ 9 ) = 0
$# 51: Code Reader Timer ( 1 ~ 120000 ) [msec]= 010000
$# 52: Code Reader Retry ( 0 ~ 10 ) = 00
$# 53: Reader1 Port No. ( 0 ~ 30 ) = 0
$# 54: Reader2 Port No. ( 0 ~ 30 ) = 0
$# 55: PCB Code Terminal = [Non] Use
$ 56: Terminal Type = [CRX1200] VT-100
$# 57: Code Terminal Port ( 0 ~ 30 ) = 0
# 70: Device Check SW =[No] Parts Miss Error
# 71: Verifier Tool = [Non] Barcode Handy_term
# 72: Barcode Reader Type ( 0 ~ 9 ) = 0
# 73: Device Check Port ( 0 ~ 30 ) = 0
# 74: ESC Permission = [Non] Permit
# 75: MAN Permission = [Non] Permit
# 76: HT Comment Term. Code ASCII CODE =
# 77: HT Verify Term. Code ASCII CODE =
# 78: D Change Trigger = Error Parts Miss PD
✩❈ 100: Pickup Position T1 ( 0 ~50000 ) [pulse]= 00000
✩❈ 101: Pickup Position T2 (-50000~0 ) [pulse]= 00000
✩❈ 102: Origin Position Z (-65000~ 65000 ) [pulse]= 00000
DATA NAME
Chapter 1 Proper Data ListingPart 4
4 – 2Version 2.0