CP43操作手册.pdf.pdf - 第6页

Contents 1.18 Nozzle T ype and Nozzle Holder Check ..................................................2–22 1.19 Backlight and Frontlight ..........................................................................2–23 2. T …

100%1 / 364
Contents
Part Two, Automatic Operation and Programming
1. Automatic Operation ...................................................................2–1
1.1 Automatic Nozzle Selection......................................................................2–1
1.1.1 Program Nozzle Diameters...........................................................2–1
1.1.2 Nozzle Reflective Disk Diameter Data (Program).........................2–2
1.1.3 Part Data Nozzle Diameters..........................................................2–2
1.1.4 Minimum Disk Diameter (Part Data)..............................................2–3
1.1.5 Automatic Selection Method..........................................................2–3
1.1.6 Forcing a Specific Nozzle..............................................................2–5
1.1.7 Nozzle Check Function .................................................................2–7
1.2 Automatic and Step Operation..................................................................2–8
1.2.1 Automatic Operation......................................................................2–8
1.2.2 Step Operation..............................................................................2–8
1.3 Recovery...................................................................................................2–9
1.3.1 Operation of Each Recovery Mode...............................................2–9
1.3.2 Insertion of Recovery Sequence .................................................2–11
1.4 Cycle Stop ..............................................................................................2–12
1.5 Device Table Mode .................................................................................2–13
1.5.1 Joint Mode...................................................................................2–13
1.5.2 Device Change Mode..................................................................2–13
1.5.3 Changeover Mode.......................................................................2–15
1.6 Loading and Unloading Boards ..............................................................2–15
1.7 Advance Pickup of Parts.........................................................................2–15
1.8 Stopping After One Board.......................................................................2–16
1.9 Scheduled Production Run.....................................................................2–17
1.10 Parts Rotation: (Pθ: Pre-theta, Fθ: Fine theta) .......................................2–18
1.11 Compensation When Picking Parts........................................................2–18
1.12 Compensation When Placing Parts........................................................2–19
1.13 Turnover Production ...............................................................................2–20
1.14 Changing Table Acceleration..................................................................2–20
1.15 Tape End Display....................................................................................2–21
1.16 Large Parts Pickup Check......................................................................2–21
1.17 Pass Mode..............................................................................................2–22
iiiVersion 5.0
FCP IV-3 Operation
Contents
1.18 Nozzle Type and Nozzle Holder Check..................................................2–22
1.19 Backlight and Frontlight..........................................................................2–23
2. Two Camera System...................................................................2–24
2.1 System Configuration .............................................................................2–24
2.2 Wide View Camera and Narrow View Camera.......................................2–24
2.2.1 Wide View Camera......................................................................2–24
2.2.2 Narrow View Camera..................................................................2–25
2.3 Data Necessary to Use the 2 Camera System.......................................2–25
2.3.1 Necessary Proper Data...............................................................2–25
2.3.2 Necessary Part Data...................................................................2–25
3. Block Skip....................................................................................2–26
3.1 Block Skip Method..................................................................................2–26
3.2 Setting Block Skip...................................................................................2–26
3.2.1 Using Machine Commands.........................................................2–26
3.2.2 Setting Automatic Block Skip Marks............................................2–28
3.3 Block Skip Specifications........................................................................2–29
3.4 Points to Remember When Using Block Skip.........................................2–30
4. Device Check...............................................................................2–31
4.1 Method and Function..............................................................................2–31
4.1.1 Performing Device Check on the Machine..................................2–31
4.1.2 The [PARTS SET] CANCEL/COMPLETE Switch .......................2–32
4.2 Setting Proper Data................................................................................2–34
4.3 Carrying Out Device Check....................................................................2–35
4.4 Permanent Set........................................................................................2–38
5. Next Device..................................................................................2–39
5.1 Setting Next Device................................................................................2–39
5.1.1 Setting Device Information Data (D_data)...................................2–39
5.1.2 Setting Sequence Information Data ............................................2–40
5.1.3 Device Table Change Trigger......................................................2–40
5.2 Next Device Operation............................................................................2–41
5.3 Points to Remember When Using Next Device......................................2–41
Version 5.0
iv
FCP IV-3 Operation
Contents
6. Nozzle Statistical Processing....................................................2–43
6.1 Nozzle Skip Method................................................................................2–43
6.2 Setting Nozzle Skip ................................................................................2–43
6.2.1 Auto-skip .....................................................................................2–43
6.2.2 Manual Nozzle Skip.....................................................................2–43
6.2.3 Setting the Error Rate..................................................................2–44
6.2.4 How to Set the Proper Data ........................................................2–44
6.2.5 Display Monitor............................................................................2–44
6.2.6 Points to Remember When Using Nozzle Skip...........................2–45
7. Fiducial Mark Recovery Command............................................2-47
7.1 How to Enter the Mark Editor Screen......................................................2-47
7.2 Proper Data Setting.................................................................................2-47
7.3 Actual Operation and the Command System..........................................2-48
7.3.1 Displaying Mark Editor Screen.....................................................2-48
7.3.2 Mark Editor Screen ......................................................................2-50
7.3.3 Description of Commands............................................................2-52
7.3.4 Cautions.......................................................................................2-53
8. Using Standard Program for Reverse Flow ..............................2-55
8.1 Using Standard Program for Reverse Flow.............................................2-55
8.2 Setting Data.............................................................................................2-56
8.2.1 Proper Data..................................................................................2-56
8.2.2 Production Program.....................................................................2-56
8.3 Cautions ..................................................................................................2-56
vVersion 5.0
FCP IV-3 Operation