CP43操作手册.pdf.pdf - 第331页

V ersion 2.0 Chapter 5 Data Check Errors Part 6 • Cam Speed Check When "Cam_speed_CP43" is checked in Part data, and the cam speed has not been entered the following err or code will display . 1 1010310 + devic…

100%1 / 364
Chapter 5 Data Check ErrorsPart 6
• Minimum Background Disk Size Check
For the device numbers being used, check that the background disk
size set in Machine_data in the production program is smaller than
the minimum background disk size set in Part data. If the results of
this check are out of range, the following equation will appear as an
error message.
1101D040 + D No/13 (Hexadecimal)
Remedy: Check the minimum background disk size set in
"Back_light_min" in Part data or check
"S_back_light_size", "M_back_light_size", and
"L_back_light_size" in Machine_data in the production
program. Input an appropriate size and retransmit the
program.
• Mark Sequence Number Check
If the number of mark sequences in the program (including both
fiducial and block skip sequences) exceeds 255, the error code
11011322 will be displayed.
Remedy: Decrease the number of mark sequences in sequence data
and then retransmit the program.
• Mark Reading Check
When a program with mark sequences is transmitted and the “Mark
Read Position X” and “Mark Read Position Y” are not found in Proper
data, error code 11011323 will be displayed.
Remedy: Eliminate the mark sequences from sequence data and
retransmit the program.
• Next Device Check
When the device data is checked and the designated number of Next
devices exceeds 30, error code 11011324 will appear.
Remedy: Designate fewer than 30 Next devices.
• Nozzle Size Check
When the nozzle size data in Machine_data (“S_nozzle_size,”
“M_nozzle_size” and “L_nozzle_size”) is checked and even one
nozzle size has not been entered, error code 11011325 will appear.
Remedy: Enter every nozzle diameter size that will be used in that
program into nozzle size data in Machine_data
(“S_nozzle_size,” “M_nozzle_size” and “L_nozzle_size”)
and retransmit the program.
6 – 30Version 2.0
Version 2.0
Chapter 5 Data Check ErrorsPart 6
• Cam Speed Check
When "Cam_speed_CP43" is checked in Part data, and the cam speed
has not been entered the following error code will display.
11010310 + device number/13
Note: Check Part data, enter the correct value for "Cam_speed_CP43 and
retransmit the corrected program.
5.2 Checking Proper Data
Any time a Proper data item moves outside its prescribed range, an error
message will appear.
Placing Position X and Placing Position Y Check
If either of these are at 0, error code 11022321 will appear.
Remedy: Carry out Proper data measurement and then transmit the
corrected Proper data.
Loading Position X and Loading Position Y Check
If either of these are at 0, error code 11023223 will appear.
Remedy: Carry out Proper data measurement and then transmit the
corrected Proper data.
Cam Speed Check
If the cam speed is less than 10% or greater than 100%, error code
11022323 will appear.
Remedy: Enter a value within this range and transmit the corrected
Proper data. Normally this value is set at 100%.
Pickup Position D1 Check
If this is set at less than -500000 or more than 0, error code 11022326 will
result.
Remedy: Carry out Proper data measurement and then transmit the
corrected Proper data.
6 – 31
Chapter 5 Data Check ErrorsPart 6
Pickup Position D2 Check
If this is set at less than 100000 or more than 300000, error code 1102233B
will result.
Remedy: Carry out Proper data measurement and then transmit the
corrected Proper data.
D1 Original Position Check
If this is set at less than -10000 or more than 10000, error code 11022328
will result.
Remedy: Carry out Proper data measurement and then transmit the
corrected Proper data.
D2 Original Position Check
If this is set at less than -10000 or more than 10000, error code 11022329
will result.
Remedy: Carry out Proper data measurement and then transmit the
corrected Proper data.
PCB Check Position X, PCB Check Position Y
If either of these are at 0, error code 1102232D will appear.
Remedy: Carry out Proper data measurement and then transmit the
corrected Proper data.
Max Limit Position X and Min Limit Position X Check
If either of these are at 0, error code 1102232E will appear.
Remedy: Carry out Proper data measurement and then transmit the
corrected Proper data.
Max Limit Position Y and Min Limit Position Y Check
If either of these are at 0, error code 1102232F will appear.
Remedy: Carry out Proper data measurement and then transmit the
corrected Proper data.
6 – 32Version 2.0