SIPLACE-SX4-DX4-用户手册.pdf - 第121页
Service Work 3.6.17 Replacing the Deflection Pulley C onveyor Service Manual SIPLACE SX4/DX4 121 3.6.17 3 . 6 . 1 7 R e p la c in g t h e D e f le c t io n P u lle y Replacing the De flection Pulley Parts, equipment and …
Service Work
Conveyor 3.6.16 Replacing the Tape Drive [03056923-xx]
120 Service Manual SIPLACE SX4/DX4
3.6.16
3.6.16 Replacing the Tape Drive [03056923-xx]
Replacing the Tape Drive [03056923-xx]
Parts, equipment and tools
▪ Tape drive, decoupled [03056923-xx]
Removal
► Use the software to move the conveyor sides into the position which allows you best access. As an
alternative, you can loosen the clamps for the relevant sides in dual conveyors.
► Switch off the machine, disconnect it from the power supply and secure it to prevent unauthorized
reactivation. Observe the instructions in section "1.2 Preparatory Work..." [ ➙ 12].
Installation
► Follow the removal instructions in reverse order for installation. Also observe the following instruc-
tions:
See also
3.6.1 Loosening the Conveyor Side Clamps [ ➙ 95]
Loosening the hexagonal shaft (using example of SX1/2)
► Loosen the fixture (2) on the hexagonal shaft (3) of
the tape drive.
► Carefully push the hexagonal shaft into the hole
drilled in the machine frame (1).
CAUTION!
There are cables run inside the machine frame.
Make sure you do not damage these cables.
Tape drive (using the example of SX1/2)
► Loosen the deflection pulley with slot (4) to relax the
conveyor belt (3).
► Loosen the screw (1) fastening the tape drive (2).
► Unthread the hexagonal shaft from the tape drive and
remove it from the machine.
CAUTION
Installation instructions
► After fitting all parts, set the toothed belt tension (see "5.5.1.1 Setting the Conveyor Belt
Tension" [ ➙ 251]).
Service Work
3.6.17 Replacing the Deflection Pulley Conveyor
Service Manual SIPLACE SX4/DX4 121
3.6.17
3.6.17 Replacing the Deflection Pulley
Replacing the Deflection Pulley
Parts, equipment and tools
▪ Deflection pulley, geared [03063837-xx]
▪ Deflection pulley, ungeared [03063838-xx]
▪ Loctite 241
Overview
Removal
► Use the software to move the conveyor sides into the position which allows you best access. As an
alternative, you can loosen the clamps for the relevant sides in dual conveyors.
► Switch off the machine, disconnect it from the power supply and secure it to prevent unauthorized
reactivation. Observe the instructions in section "1.2 Preparatory Work..." [ ➙ 12].
► Loosen the screw fastening the deflection pulley with slot.
► Loosen the fastening screw on the deflection pulley to be replaced.
► Unthread the deflection pulley from the conveyor toothed belt and remove it.
Installation
► Follow the removal instructions in reverse order for installation. Also observe the following instruc-
tions:
See also
3.6.1 Loosening the Conveyor Side Clamps [ ➙ 95]
1. Deflection pulleys, ungeared (4x per side)
2. Deflection pulleys, geared (4x per side)
CAUTION
Toothed belt
► Make sure that the toothed belt is not folded or otherwise damaged.
CAUTION
Installation instructions
► Make sure that the toothed belt is not folded or otherwise damaged.
► After fitting all parts, set the toothed belt tension. (See "5.5.1.1 Setting the Conveyor Belt
Tension" [ ➙ 251])
► Secure with screws with Loctite 241.
Service Work
Conveyor 3.6.18 Replacing the Hexagonal Shaft [03057258-xx]
122 Service Manual SIPLACE SX4/DX4
3.6.18
3.6.18 Replacing the Hexagonal Shaft [03057258-xx]
Replacing the Hexagonal Shaft [03057258-xx]
Parts, equipment and tools
▪ Hexagonal shaft assembly [03057258-xx]
Removal
► Use the software to move the conveyor sides into the position which allows you best access. As an
alternative, you can loosen the clamps for the relevant sides in dual conveyors.
► Switch off the machine, disconnect it from the power supply and secure it to prevent unauthorized
reactivation. Observe the instructions in section "1.2 Preparatory Work..." [ ➙ 12].
Installation
► Follow the removal instructions in reverse order for installation.
See also
3.6.1 Loosening the Conveyor Side Clamps [ ➙ 95]
Hexagonal shafts (using example of SX1/SX2)
► Loosen the fastening (2) on the hexagonal shaft (3).
► You can now carefully push one side of the hexago-
nal shaft into the hole in the machine frame (1) and
thread it out of the conveyor sides, together with the
bearing.
CAUTION!
There are cables run inside the machine frame.
Make sure you do not damage these cables.