SIPLACE-SX4-DX4-用户手册.pdf - 第162页

Service Work Cutter 3.9.6 Replacing the Proximity Switch [03063 590] 162 Service Manual SIPLACE SX4/DX4 3.9.6 3 . 9 . 6 R e p la c in g t h e P r o x im it y S w it c h [ 0 3 0 6 3 5 9 0 ] Replacing the Proxim ity Switch…

100%1 / 298
Service Work
3.9.5 Replacing the Solenoid Valves [03000630-xx] Cutter
Service Manual SIPLACE SX4/DX4 161
► Connect the compressed air hoses to the cylinder in the correct allocation.
► Further installation is performed by following the above instructions in the reverse order. Also ob-
serve section "3.9.3 Replacing the Articulated Joint on the Short-Stroke Cylinder [03000518-xx]"
[ ➙ 158].
3.9.5
3.9.5 Replacing the Solenoid Valves [03000630-xx]
Replacing the Solenoid Valves [03000630-xx]
Parts, Equipment and Tools
▪ Solenoid valve [03000630-xx]
Overview
Removal/Installation
► Loosen the compressed air connections on the solenoid valve.
► Unplug the press-fit connection on the solenoid valve connection cable.
► Loosen the screws holding the solenoid valve in place and remove the solenoid valve.
► Mount the new solenoid valve and make the press-fit connection to the valve.
Attach cables ties, if necessary (strain relief).
► Install the proximity switch (1) precisely in the position
you marked with the permanent marker.
► Place the prepared cylinder into the cutter, in the cor-
rect rotary position of the articulated joint (2).
► Fasten the cylinder in this position, with the two
screws provided (3) (Loctite 241).
1
3
2
Cutter (using example of X series)
1. Position of the solenoid valves
Service Work
Cutter 3.9.6 Replacing the Proximity Switch [03063590]
162 Service Manual SIPLACE SX4/DX4
3.9.6
3.9.6 Replacing the Proximity Switch [03063590]
Replacing the Proximity Switch [03063590]
Parts, equipment and tools
▪ Proximity switch with cable (incl. four signal transmitters) [03063590-xx]
Overview
Removal/installation
Cutter (using example of X series)
1. Two proximity switches on each short-stroke cylinder
► To make subsequent checking easier, use a perma-
nent marker to mark the exact installation position (3)
of the proximity switch (1) or (2) on the short-stroke
cylinder.
► Loosen the screw fastening the proximity switch to
the short-stroke cylinder.
► Unplug the connection cable.
► Fit the proximity switch at the positions shown in the
following diagram. These should match the positions
marked (3).
► Secure the fastening screws with locking varnish.
► Reconnect to the electricity supply.
► Check the switching points of the proximity switches.
1
2
3
3
Service Work
3.9.7 Replacing the Cutter Blades Cutter
Service Manual SIPLACE SX4/DX4 163
3.9.7
3.9.7 Replacing the Cutter Blades
Replacing the Cutter Blades
Parts, equipment and tools
Select the right set of blades.
We recommend the following additional spare parts:
▪ 2x blade cover (cutter HF) [03000553-xx] (cover for screws of movable blades)
▪ 2x ISO4762-M5x35-12.9, geomet 321+VL [03057290-xx] (screws for movable blades)
▪ 2x articulated joint (cutter HF) [03000518-xx]
▪ 2x DIN71412-BM6 [03036943-xx] (lubrication nipple)
Consumables required:
▪ Lubricant grease Klüber BEM 34-132 tin 1 kg [00374565-xx] (identical to the lubricant grease used
on the guide carriage of the gantry)
▪ Interflon Fin Grease [03020782-xx]
▪ LOCTITE 243 screw locking varnish [00334892-xx]
Tools required
▪ Extra protection gloves, leather [00091001-xx]
▪ Torx screwdriver ESD 1.0-5.0 Nm [03078400-xx]
▪ Torque wrench 2.5 - 25 Nm [00376625-xx]
▪ Bit holder for TorqueVario screwdriver [03078706-xx]
▪ Socket-head bit size 3-6
▪ Fork wrench, size 10
▪ Feeler gauge
▪ Brush
▪ Cloth
▪ Two large parallel clamps and a sturdy table with even surface, to clamp down the dismantled cutter
CAUTION
Risk of injury!
There is a high risk of injury from the blades and the tape deflector.
► Wear appropriately thick protective gloves!
► Never reach into the cutter from below or into the empty-tape duct from above.
► Make sure that no-one can injure themselves on the cutter after it has been dismantled and
placed next to the machine!
NOTICE
Turn the blade
The fixed and movable blades have been sharpened on both sides. If one side becomes blunt,
you can rotate the blade by 180 degrees to use the other side.
Machine Tape cutter, pneumatic Function status Set of blades
X series, SX4, DX4, X
series S
03066690-xx(without CAN nodes) -01 03009259-xx
HF, X series 03000487-xx -01 to -03 03000501-xx
-04 to -05 03009259-xx
X Series 03019941-xx(with control unit) -01 03009259-xx
03052900-xx(with CAN nodes) -01 to -02 03009259-xx