SIPLACE-SX4-DX4-用户手册.pdf - 第168页
Service Work Cutter 3.9.8 Replacing the Used Tape Chute [03067460- xx] 168 Service Manual SIPLACE SX4/DX4 3.9.8 3 . 9 . 8 R e p la c in g t h e U s e d T a p e C h u t e [ 0 3 0 6 7 4 6 0 - x x ] Replacing the Used Ta pe…
Service Work
3.9.7 Replacing the Cutter Blades Cutter
Service Manual SIPLACE SX4/DX4 167
► Push the spacers (with inserted feeler gauges) as far as possible in the direction of the moveable
blade. The maximum permissible gap is 1.0 mm.
► Now tighten the four screws (4) crosswise at the downholder.
► Remove the two feeler gauges.
► Insert the new stationary blade (5) in the correct position and screw tight.
Final Work:
If the gap is correct:
► Fit the baffle plate and cover plate. Make sure that the edges are parallel.
► Remove the clamps form the cutter/ remove the cutter from the assembly plate.
► Further installation is performed by following the above instructions in the reverse order.
See also
3.10.1 Replacing the COT Insert Assembly [03080552-xx] [ ➙ 170]
Cutter (using example of X series)
► Use a feeler gauge to check the gap between the
tape deflector (1) and the moveable blade (2), along
the entire length and width of the blade.
⇨ The 0.05 mm feeler gauge should fit through the
gap.
⇨ The 0.25 mm feeler gauge should not fit through
the gap.
If the gap is not correct, check:
▪ Whether the wrong holding-down device has been in-
stalled (with function status < 03)
▪ The holding-down devices are those designed for
cutters with function status -04 (= with tape deflector)
▪ Whether the blades, tape deflector etc. were cleaned
before installation
1
2
CAUTION
Check how the cables are run!
Make sure that the cables and hoses are not pinched or subjected to excess strain.
Service Work
Cutter 3.9.8 Replacing the Used Tape Chute [03067460-xx]
168 Service Manual SIPLACE SX4/DX4
3.9.8
3.9.8 Replacing the Used Tape Chute [03067460-xx]
Replacing the Used Tape Chute [03067460-xx]
Parts, equipment and tools
▪ Use tape chute assembly [03067460-xx]
▪ Allen key set
Overview
SXDX4
1 Waste slide 2 COT insert
3 Manual Table for DX4 4 Fastening screw for used tape chute, left
5 Fastening screw for used tape chute, right
Service Work
3.9.8 Replacing the Used Tape Chute [03067460-xx] Cutter
Service Manual SIPLACE SX4/DX4 169
Removal
► Loosen the screw fastening the used tape chute
► Take the used tape chute down and out of the machine.
Installation
► Follow the removal instructions in reverse order for installation.
See also
3.13.2 Removing the Back Section of the Manual Table [ ➙ 201]
3.13.3 Removing the Front Section of the Manual Table [ ➙ 202]
3.13.6 Replacing the Feeder Control Unit (FCU) [ ➙ 206]
3.10.3 Replacing the 40-Fold Feeder Unlock Device [03011582-xx] [ ➙ 173]
CAUTION
Risk of cutting
The cutter is located under the tape channel. The blades there have very sharp edges.
► Do not reach into the cutter and make sure that it is never freely accessible for longer peri-
ods.