SIPLACE-SX4-DX4-用户手册.pdf - 第41页
Service Work 3.2.5 Replacing the AC/DC Converter ( Pulsed Power Packs A5 to A 8) Electrical System Service Manual SIPLACE SX4/DX4 41 Removal ► Switch off the machine, disconnec t it from the po wer supply and secure it t…
Service Work
Electrical System 3.2.5 Replacing the AC/DC Converter (Pulsed Power Packs A5 to A8)
40 Service Manual SIPLACE SX4/DX4
3.2.5
3.2.5 Replacing the AC/DC Converter (Pulsed Power Packs A5 to A8)
Replacing the AC/DC Converter (Pulsed Power Packs A5 to A8)
Parts, equipment and tools
▪ AC/DC converter (pulsed power pack – A5, A6, A7) [03055232-xx]
▪ AC/DC converter (pulsed power pack – A8) [03076588-xx]
Overview
SX4 X34iS – Ov erview of Pul sed Power Pac ks
The pulsed power packs are located in the rack unit be-
tween location 3 and 4.
A5) Pulsed power pack (24 VDC, set to 25 VDC)
for Power Fail, safety circuit SSK, tape cutter, PCB Han-
dling
The power fail signal is generated by the pulsed power
pack A5 and sent to the GCU and HCU. (X200:9,
X200:10)
A6) Pulsed power pack (27 VDC)
for FCU (gantry 1 and 4)
A7) Pulsed power pack (27 VDC)
for FCU (gantry 2 and 3)
A8) Pulsed power pack (36 VDC, to be set to 42 VDC)
For HCU (gantry 1 to 4)
NOTICE!
NOTICE! Check the set values and correct if
necessary.
To A5:
The following fuses have 24 V present:
F10: Conveyor electrics
F11: Y motor fan, safety circuit (internal)
F12: Distributor power (line 1)
F13: Distributor power (line 2)
F14: Power fail
F20: Cover fan, gantry 1 and 4
F21: Cover fan, gantry 2 and 3
Service Work
3.2.5 Replacing the AC/DC Converter (Pulsed Power Packs A5 to A8) Electrical System
Service Manual SIPLACE SX4/DX4 41
Removal
► Switch off the machine, disconnect it from the power supply and secure it to prevent unauthorized
reactivation. Observe the instructions in section "1.2 Preparatory Work..." [ ➙ 12].
► Unplug all connections to the module. You may want to mark their positions, to make clear assign-
ment easier later on.
Installation
► Follow the removal instructions in reverse order for installation. Also observe the following instruc-
tions:
► To release the module, press the lever (1) at the back
of the module down and then pull the module off the
rail.
CAUTION
Installation instructions
► Set the voltage. (See "5.2.2 Setting the Voltage on the Pulsed Power Packs" [ ➙ 234])
Service Work
Electrical System 3.2.6 Replacing the Rectifiers (U1 to U3, U20 to U24)
42 Service Manual SIPLACE SX4/DX4
3.2.6
3.2.6 Replacing the Rectifiers (U1 to U3, U20 to U24)
Replacing the Rectifiers (U1 to U3, U20 to U24)
Parts, equipment and tools
▪ U1, U3: rectifier S101-B6U 160-08 [00341246-xx]
▪ U2: rectifier S61-B2U 28-10 [03080931-xx]
▪ U20 to U24: rectifier S61-B2U 28-04 [03079959-xx]
▪ Silicon-free heat-conductive paste (not electrically conductive)
Thermal conductivity 1.0 W/mK
Dielectric strength 40kV/mm
Temperature range -40°C to +200°C
Flash point >280°C
Suggested supplier: Bürklin OHG, order number 80 B 531
Overview
Removal
► Switch off the machine, disconnect it from the power supply and secure it to prevent unauthorized
reactivation. Observe the instructions in section "1.2 Preparatory Work..." [ ➙ 12].
► Loosen the screws fastening the cover and swing the cover towards the front. The pulsed power
packs are fitted to the cover. These are swung open together with the cover.
► Unplug all connections to the rectifiers. You may want to mark their positions, to make clear assign-
ment easier later on.
► Loosen the screws fastening the rectifier and remove the rectifier.
Installation
► Follow the removal instructions in reverse order for installation. Also observe the following instruc-
tions:
1. Cover
2. Rectifier U24
3. Rectifier U3
4. Rectifier U1
5. Rectifier U2
6. Rectifier U20 to U23
CAUTION
Installation instructions
► Apply a heat-conductive paste between the metal frame and the rectifier.