SIPLACE-SX4-DX4-用户手册.pdf - 第144页
Service Work Placement heads 3.7.3 Replacing the CPP Head 144 Service Manual SIPLACE SX4/DX4 Installation ► Follow the removal in structions in reverse order for installati o n. Also observe the following instruc - tions…
Service Work
3.7.3 Replacing the CPP Head Placement heads
Service Manual SIPLACE SX4/DX4 143
► Loosen all four screws fastening the head with a long Torx screwdriver.
► Carefully lift the head out of the locating pins on the head plate/from the hook.
► Fit the protective cap onto the component sensor for
the placement head.
► Unplug the compressed air connections (1) from the
placement head. You may want to mark the positions,
to make clear assignment easier later on.
► Disconnect the flat ribbon cables (3) from the inter-
mediate distributor (2). You may want to mark the po-
sitions, to make clear assignment easier later on.
► Loosen the screws fastening the strain relief (2) on
the component camera cable (1) and carefully unplug
the cable. While unplugging the cable, press the
clamps on both sides of the connector (3). You may
want to mark the positions, to make clear assignment
easier later on.
NOTICE
Additional work
► If you need to perform further work on this head (e.g. replacing spare parts), fit the head to
the head mount [03056231-xx].
Service Work
Placement heads 3.7.3 Replacing the CPP Head
144 Service Manual SIPLACE SX4/DX4
Installation
► Follow the removal instructions in reverse order for installation. Also observe the following instruc-
tions:
See also
3.7.3.1 Preparing the Head for the Installation Height [ ➙ 145]
3.7.5 Installation Positions on the Head Plate [ ➙ 149]
3.7.2 Replacing the C&P20/A/M Head [ ➙ 139]
3.7.4 Replacing the Twin/VHF Head [ ➙ 146]
3.7.5 Installation Positions on the Head Plate [ ➙ 149]
CAUTION
Installation instructions
► Observe the correct installation height of the head! Read the service manual for your place-
ment head for more information.
► If you replace the head without the component camera, you will need to fit the old camera
onto the new head. Read the service manual for your placement head for more information.
► Make sure that the assembly position on the head plate is correct.
► Tighten the four fastening screws with a torque of 270 Ncm.
► Make sure that the flat ribbon cable is run correctly to the head adapter (see below).
Correct running of flat ribbon cable to head adapter
► Make sure that the flat ribbon cable is run correctly to
the head adapter. In particular, the cables must lie in-
side one another at the 90 degrees turn (1) and not
on top of one another, otherwise the connections on
the head adapter could be easily confused.
Service Work
3.7.3 Replacing the CPP Head Placement heads
Service Manual SIPLACE SX4/DX4 145
3.7.3.1
3.7.3.1 Preparing the Head for the Installation Height
Preparing the Head for the Installation Height
Overview
CAUTION
Different heights
The placement head can be installed at two different heights. CPP_L corresponds to a compo-
nent height of six mm. CPP_H corresponds to a component height of 11.5 mm.
If the CPP head is used in a placement area with stationary camera, TwinHead or WPC, it may
only be used in the upper position.
1. Fastening screws on the left side
2. Fastening screws on the right side
This diagram shows the fastening screws in the "head at
top" position.
1. Holding bracket
2. "Head at bottom" position
3. "Head at top" position
4. Fixture holes with bushings