SIPLACE-SX4-DX4-用户手册.pdf - 第62页
Service Work Control 3.3.5 Replacing the Monitor [03078913-xx] 62 Service Manual SIPLACE SX4/DX4 3.3.5 3 . 3 . 5 R e p la c in g t h e M o n it o r [ 0 3 0 7 8 9 1 3 - x x ] Replacing the Monitor [03078913-xx] Parts, Equ…
Service Work
3.3.4 Replacing the BoxPC Memory Extension [03086337-xx] Control
Service Manual SIPLACE SX4/DX4 61
3.3.4
3.3.4 Replacing the BoxPC Memory Extension [03086337-xx]
Replacing the BoxPC Memory Extension [03086337-xx]
Parts, equipment and tools
▪ Working memory SO-DIMM DDR2 667, 1024MB [03086337-xx]
Overview
Removal
► Switch off the machine, disconnect it from the power supply and secure it to prevent unauthorized
reactivation. Observe the instructions in section "1.2 Preparatory Work..." [ ➙ 12].
► Dismantle and remove the BoxPC from the machine.
(See Replacing the Control Computer BoxPC [03084494-xx])
► Loosen the two screws fastening the cover of the BoxPC and open the cover.
► Loosen the locks on both sides of the memory extension and remove the memory extension.
Installation
► Follow the removal instructions in reverse order for installation. Also observe the following instruc-
tions:
See also
3.3.2 Replacing the CAN Card [03079973-xx] [ ➙ 59]
3.3.1 Replacing the Control Computer BoxPC [ ➙ 57]
1. Memory extension
CAUTION
Installation instructions
► Make sure that you insert the memory extension the right way round. The new memory ex-
tension must audibly engage into its slot.
Service Work
Control 3.3.5 Replacing the Monitor [03078913-xx]
62 Service Manual SIPLACE SX4/DX4
3.3.5
3.3.5 Replacing the Monitor [03078913-xx]
Replacing the Monitor [03078913-xx]
Parts, Equipment and Tools
▪ Monitor SCD1520-TDC [03078913-xx]
Overview
Removal
► Switch off the machine, disconnect it from the power supply and secure it to prevent unauthorized
reactivation. Observe the instructions in section "1.2 Preparatory Work..." [ ➙ 12].
► Unplug all connections to the monitor. You may want to mark their positions, to make clear assign-
ment easier later on.
► Loosen the upper and lower screws fastening the monitor bracket to the machine and lift the monitor
and its bracket out of the keyholes.
► Loosen the four screws fastening the monitor to its bracket. You will need the monitor bracket when
fitting the new monitor.
Installation
► Follow the removal instructions in reverse order for installation.
1. Monitor
2. Screws fastening the monitor bracket to the machine
3. Monitor connections
4. Screws fastening the monitor to the bracket
Service Work
3.4.1 Pneumatic System - Overview Pneumatic System
Service Manual SIPLACE SX4/DX4 63
3.4
3.4 Pneumatic System
Pneumatic System
Pneumat ic System - Using th e Correc t Blanking Plugs
3.4.1
3.4.1 Pneumatic System - Overview
Pneumatic System - Overview
The pneumatic system is located at locations 1, 3 and 4, behind the side covers.
CAUTION
Switch off the compressed air supply.
When working on the pneumatic system, always disconnect the machine from the compressed
air supply.
CAUTION
Use the correct blanking plugs
► Only use blanking plugs in the machine which match the manufacturer's compressed air
connection. A tight fit cannot be guaranteed for other blanking plugs.
► We recommend the use of blanking plugs made by Festo.
1. Location 3, behind the side cover: Elmo blower with
electrics, cooling air filter
2. Location 4, behind the side cover
3. Proportional controller for gantry group of placement
heads PA1/PA2
1. Location 1, behind the side cover: connection cou-
pling, main valve with compressed air filter, com-
pressed air displays
2. Location 1, at the bottom, in the machine base: com-
pressed air connection for gantry trailing cable and
vacuum pump option
3. 5/2 way valve [03062277-xx]
Main valve (X59) for NC, input, conveyor
4. 5/2 solenoid valve [00344974-xx]
Safety valve (X60) for tape cutter
5. Pressure regulator [03062103-xx]