SIPLACE-SX4-DX4-用户手册.pdf - 第96页

Service Work Conveyor 3.6.1 Loosening the Conveyor Side Clamps 96 Service Manual SIPLACE SX4/DX4 3.6.1.1 3 . 6 . 1 . 1 M a n u a lly M o v in g t h e C o n v e y o r S id e s w it h t h e H e lp o f t h e A d ju s t m e …

100%1 / 298
Service Work
3.6.1 Loosening the Conveyor Side Clamps Conveyor
Service Manual SIPLACE SX4/DX4 95
3.6
3.6 Conveyor
Conveyor
Conveyo r X-Series S, SX-Ser ies, DX-S eries – Ca ution: Moving the Conveyor Sides
3.6.1
3.6.1 Loosening the Conveyor Side Clamps
Loosening the Conveyor Side Clamps
Many tasks performed on the conveyor require that the conveyor sides are moved when the machine is
switched off. The clamps on the conveyor sides of dual conveyors can be released for this.
0100 - SXDX12V1V2 SXDX4 X34iS
Conveyo r X-Series S, SX-Ser ies, DX-S eries – Ca ution: Moving the Conveyor Sides
CAUTION
Moving the conveyor sides
The conveyor sides are highly sensitive and may not be moved unless you have released the
brakes. If you do move them without releasing the brakes, this could cause irreparable damage
to the conveyor sides.
► We recommend that you use the software to help you move the conveyor sides.
► If you are not able to do this, the conveyor sides of dual conveyors can also be moved by
manually docking in the adjustment units. Make sure that the cylinders in all clamping units
of a particular side engage. The conveyor sides can then be moved by carefully pulling on
the toothed belt of the width adjustment unit.
► If you are not able to do this, the brakes of dual conveyors can also be manually released
using a pin. Take special care not to distort the conveyor sides.
CAUTION
Lifting table
► The lifting table must always be lowered when the conveyor sides are moved.
NOTICE
Single conveyor
There are no clamps on a single conveyor.
► You can move the flexible side here by carefully pulling on the width adjustment toothed
belt.
CAUTION
Moving the conveyor sides
The conveyor sides are highly sensitive and may not be moved unless you have released the
brakes. If you do move them without releasing the brakes, this could cause irreparable damage
to the conveyor sides.
► We recommend that you use the software to help you move the conveyor sides.
► If you are not able to do this, the conveyor sides of dual conveyors can also be moved by
manually docking in the adjustment units. Make sure that the cylinders in all clamping units
of a particular side engage. The conveyor sides can then be moved by carefully pulling on
the toothed belt of the width adjustment unit.
► If you are not able to do this, the brakes of dual conveyors can also be manually released
using a pin. Take special care not to distort the conveyor sides.
Service Work
Conveyor 3.6.1 Loosening the Conveyor Side Clamps
96 Service Manual SIPLACE SX4/DX4
3.6.1.1
3.6.1.1 Manually Moving the Conveyor Sides with the Help of the Adjustment Units
Manually Moving the Conveyor Sides with the Help of the Adjustment Units
Docking in the adjustment units
If you are unable to move the sides with the software (e.g. due to a sensor error), proceed as follows:
► Switch off the machine.
► Switch off the BoxPC.
► Create access for the solenoid valves to the adjustment units:
SX1/SX2: Dismantle the lifting table plate at location 2.
SX4/DX4: Dismantle the cover next to the lifting table plate at location 4.
X-Series S: Dismantle the lifting table plate at location 3.
► Switch the machine on (without BoxPC). The machine is now supplied with compressed air.
Solenoid valves (example of SX1/SX2 shown)
► Carefully pull on the width adjustment belt to move
the adjustment units until they are under the clamps
and the short-stroke cylinder can activate the clamps.
► Operate the solenoid valves (individually if needed)
using the yellow slide switches (1). This moves the
cylinders out, which then loosen the clamps.
► Make sure that all side cylinders (1) have engaged.
NOTICE!
The adjustment units need to be positioned under the
conveyor side so that all engage at the same time. If this
is not possible, check the parallelism of the adjustment
units. If these are OK, the conveyor side may be distort-
ed. In this case, call the SIPLACE Service team.
► Carefully pull on the width adjustment belt to move
the conveyor side.
► Repeat these steps if needed for any other conveyor
sides.
Service Work
3.6.1 Loosening the Conveyor Side Clamps Conveyor
Service Manual SIPLACE SX4/DX4 97
3.6.1.2
3.6.1.2 Moving the Conveyor Sides by Manually Releasing the Side Clamps
Moving the Conveyor Sides by Manually Releasing the Side Clamps
0220 - Parts etc. - SXDX4
Parts, equipment and tools
▪ Depending on your clamping version, you may need the following per side:
3x ISO4762-M3x35-A2-70 [03043114-xx] or
3x ISO8734-3x30-A-ST [03015760-xx]
Procedure
► Move the conveyor sides to a position which gives you good access to the clamps.
► Switch off the machine, disconnect it from the power supply and secure it to prevent unauthorized
reactivation. Observe the instructions in section "1.2 Preparatory Work..." [ ➙ 12].
► Repeat these steps for all clamps on the sides concerned.
NOTICE
Marking the starting positions
After completing this task, it is helpful to move the conveyor sides back to their approximate
starting positions.
► You may want to mark the current positions of the conveyor sides.
Do not mark the clamping surface or the guide rails.
CAUTION
Loosen all clamps
You always need to loosen all clamps for one conveyor side.
► Loosen the conveyor side clamps.
To do this, press the clamp (1) (e.g. with a screwdriv-
er) upwards and turn or insert a screw (M3x16) into
the hole (2).
CAUTION!
Make sure that you do not distort the guide plate (3). If
you do, this could lead to problems with recognizing the
position of the conveyor side.
CAUTION
Always loosen all clamps for one conveyor side!
► Always loosen all clamps for one conveyor side!
SX1/SX2/DX1/DX2: 2 clamps per conveyor side
SX4/DX4/X series S: 3 clamps per conveyor side.
► If you do not loosen all clamps for the conveyor side, this could be easily damaged.