00198227-03_UM_MaterialSetupAssistant_2.3-R17-1_DE_EN.pdf - 第158页

Preconditions and Configuratio ns Configuration Settings in ASM Setup Center 158 ASM Material Setup Assistant 2.3 (R17-1) ASM Material Setup Ass i st a n t 2 . 3 2.2.3 2 . 2 . 3 C o n f ig u r in g F e e d e r R a c k s …

100%1 / 242
Preconditions and Configurations
Configuration Settings in ASM Setup Center
ASM Material Setup Assistant 2.3 (R17-1) ASM Material Setup Assistant 2.3 (R17-1) 157
Printing the setup report starts material supply task
Disabled: Default setting
Enabled: The material supply task is automatically set to the status "started" once the setup report is
printed. Thus, SIPLACE Material Setup Assistant is notified that the material supply task has been start
-
ed.
Workflow with ASM Material Manager for MSA
► For the workflow with ASM Material Manager for MSA, enable the Printing the setup report starts
materials supply task option.
The printout of the setup report is used as the order form for the other material management system
und the customer uses it to start the material procurement. Thus, it is ensured that the material which
is ordered via the setup report is used.
Mark location as completed at the start of the verification task
Once a location is fully verified, this is registered in the setup job in Material Setup Assistant, increasing
the progress of this setup job. Once all locations have been verified, the setup job progress will be shown
as 100%. This means that the setup job has been completed. The time taken to complete the presetup
process can be seen in Monitoring.
If a location is not fully verified, for example when certain MSD materials are scheduled for subsequent
configuration at the line, this location can not be marked as completed in the Material Setup Assistant.
The operator then needs to scan in the "end barcode".
To avoid this, enable this option.
The location will be marked as completed, as soon as you start the presetup process. You do not need
to scan in the "end barcode".
However, this means that the presetup job appears in Monitoring as if it were completed, while the last
location is still being configured.
Register material for other location
Option for the workflow with ASM Material Manager for MSA with the scan workflow Sort material.
Disabled: The scan workflow Sort material only records reels for the current location. For packaging units
that are used on other locations, the user receives a hint as to where the packaging unit is used. The
user can freely decide where the packaging unit is to be used.
Enabled: During the scan workflow Sort material, the packaging unit for the other recognized location is
registered and will be taken into account during a recalculation of the material demand.
Assigning the pre-setup area for this Setup Center application
The storage zone for the presetup area must have been created in the factory layout of the Factory Ex
-
plorer. Multiple presetup areas can be present as storage zone within the same production environment.
See also "2.1.2 Defining the Factory Layout" [ ➙ 137]
Docking area according to factory layout shows all the Storage zones for the factory layout.
► Go to Docking area according to factory layout and select the presetup area which is assigned to
this Setup Center application.
Preconditions and Configurations
Configuration Settings in ASM Setup Center
158 ASM Material Setup Assistant 2.3 (R17-1) ASM Material Setup Assistant 2.3
2.2.3
2.2.3 Configuring Feeder Racks
Configuring Feeder Racks
► Go to the main menu and select Extras > Settings to open the Settings window.
► Select the category Feeder Racks and the settings are opened.
Settings - Feeder Rack
► The Material Reuse mode (1) must be activated for the feeder racks used. Correct this setting, if nec
-
essary.
⇨ In connection with the SIPLACE Material Setup Wizard, this feeder rack is used as AFP hardware
in the pre-setup area. In this feeder rack, set-up feeders are parked for a later reuse.
► For detailed information on the configuration of the feeder racks, please refer to the ASM Setup
Center user manual or to the ASM Setup Center online help.
Preconditions and Configurations
Configuration Settings in ASM Setup Center
ASM Material Setup Assistant 2.3 (R17-1) ASM Material Setup Assistant 2.3 (R17-1) 159
2.2.4
2.2.4 Configuring the ASM Setup Center Server
Configuring the ASM Setup Center Server
Configure the communication between ASM Setup Center and the systems involved with the SIPLACE
Material Setup Assistant workflow. Enable and configure the OIB Core at ASM Setup Center Server.
► In the task bar, open the ASM Setup Center context menu and start Custom Configuration => Setup
Center Server (1).
Custom Configuration – Start Setup Center Server