SM-131-006.pdf - 第125页
Device Name Chip Mounter Block Name Page No. Unit Name Revision Model Item GXH -1 Chapter 5 Head Section 7. MSB W hole Cleaning and Lubricat ion Procedures (3) Return all nozzles used for the noz zle lev el teaching to t…
Device
Name
Chip Mounter
Block Name
Page No.
Unit Name
Revision
Model Item GXH-1
Chapter 5 Head Section
7. MSB Whole Cleaning and Lubrication Procedures
7.3 Operation Procedures
(1) First, attach 12 nozzles in the same type to the head to perform cleaning and lubrication
at the [SETUP] => [NOZZLE] tab sheet below. (No matter the nozzle types, perform the
nozzle level teaching operation.)
Fig. E47
(2) Open the [MAINT] => [TEACHING] => “Nozzle Level Offset” tab sheet below
(Fig.E48) and select the head No. and all nozzles to perform cleaning and lubrication.
Perform the teaching operation of the nozzle level offset, after that save the data.
*This data saved is used for a confirmation of the difference between “Before
lubrication” data and “After lubrication” data after cleaning and lubrication operations.
Fig. E48
Save this data of
“Before lubrication”
after teaching
0605-001
5-23
Device
Name
Chip Mounter
Block Name
Page No.
Unit Name
Revision
Model Item GXH-1
Chapter 5 Head Section
7. MSB Whole Cleaning and Lubrication Procedures
(3) Return all nozzles used for the nozzle level teaching to the stocker by the [Reset Nozzle]
button in the [SETUP] => [NOZZLE] tab sheet. Then, remove the feeder carts around
the cleaning sections to work smoothly.
(4) Turn off the machine and break the air.
(5) Detach the machine safety guard cover located to the cart upper section.
(6) Detach the head cover (See Fig. E49 below). This section has been fixed with SUS 4-
M3×L6 truss screws. (Applied 1401B screw lock)
Common use of Head covers: Head No.1 and 4, Head No.2 and 3
The head cover is set so that the cutting section turns up. Therefore, please pay attention
to the up/down directions when attaching this part (in reverse operation).
Fig. E49
Fig. E50
0605-001
5-24
Head Cover
Do not allow to hit this safety guard cover to
the linear scale located to the machine Y-axis
both sides in detaching operation. See
Volume 4 Trouble Shooting (3.3: Fig. 4A28).
Device
Name
Chip Mounter
Block Name
Page No.
Unit Name
Revision
Model Item GXH-1
Chapter 5 Head Section
7. MSB Whole Cleaning and Lubrication Procedures
(7) Detach the large and small diffusion plates. (See Fig. E51 below)
(Large: 3-M1.6×L4 Bolts, Small: 2-M1.6×L4)
There might have been cases where the screw lock (Three Bond 1401B) applied last time
has protruded to the bolt fixing section and adhered to the attaching surface of the
diffusion plates. In this case, please be careful not to force the diffusion plates to detach
because it will cause damages of diffusion plates and the screw lock adhered on the
surface
must be removed cleanly.
View of Head Bottom Surface
Fig. E51
0605-001
5-25
M1.6×L4
Exercise adequate care in detaching the small diffusion plate not to
damage. Especially, we recommend applying a wrench to the transparent
section of the light emission section tip side surface or covering the section
with
p
lastic wra
p
to
p
rotect.
! Caution
Large Diffusion Plate
Small Diffusion Plate
M1.6×L4