SM-131-006.pdf - 第76页
Device Name Chip Mounter Block Name Page No. Unit Name Revision Model Item GXH-1 1.1 Setting of Servoamplifiers • Set CS1 (axis selection switch) as shown in Table C1. See Fig. C1. Table C1 Servoamplifiers Location Symbo…
0406-001 3-B
Device
Name
Chip Mounter
Block Name
Page No.
Unit Name
Revision
Model ItemGXH-1
1.1 Setting of Servoamplifiers
• Set CS1 (axis selection switch) as shown in Table C1. See Fig. C1.
Table C1
Servoamplifiers
Location Symbol Name
CS1 Arrow
Directions
-A21 X-Axis Amplifier １
-A22 Y1-Axis Amplifier 2
CA
-A23 Y2-Axis Amplifier 3
-A21 X-Axis Amplifier 4
-A22 Y1-Axis Amplifier 5
CB
-A23 Y2-Axis Amplifier 6
-A21 X-Axis Amplifier １
-A22 Y1-Axis Amplifier 2CC
-A23 Y2-Axis Amplifier 3
-A21 X-Axis Amplifier 4
-A22 Y1-Axis Amplifier 5
CD
-A23 Y2-Axis Amplifier 6
-A63 Side A Cutter Axis Amplifier 6
BA
-A63 Side B Cutter Axis Amplifier 6
-A63 Side C Cutter Axis Amplifier 6
BC
-A63 Side D Cutter Axis Amplifier 6
NA -A53 NA Backup Axis Amplifier 5
NC -A53 NC Backup Axis Amplifier 5
Fig. C1 Servoamplifier
0406-001
Chapter 3 Various Setting
1. Setting of Servoamplifiers
3-1
Axis Selection Switch
Device
Name
Chip Mounter
Block Name
Page No.
Unit Name
Revision
Model ItemGXH-1
Chapter 3 Various Setting
2. Setting of Various Boards
2.1 Table of Boards with Various Adjusting Switches
Table of Boards with Various Adjusting Switches Table C2
Board Types
No.
Board
Symbols
Board Names
U NO Location
Reference
Item Nos.
1 UB20 Relay Board 1 U26 BH Section (Center below
Frame on Rear Side)
2.2
2 UB21 Relay Board 2 U27 Power Supply Section (One
Board each for BL and BR)
2.3
3 UA54 ILB Board U05 Power Supply Section (One
Board each for BL and BR)
2.4
4 UB14 I/O Board U12 Power Supply Section (One
Board each for BL and BR)
2.5
5 UB14 I/O Board U08 Transfer Section 2.5
6 UB14 I/O Board U09 Cutter/Positioning Section 2.5
7 UB13 I/O Board U01 Operation Panel Front/Rear 2.6
8 UB13 I/O Board U11 Light Tower 2.6
9 UA53 I/F Board U07 Signals between Main Machine
and Input/Output Machines
2.7
10 UB22 I/O Board U04 Head (Doughnut Board) 2.8
11 Multiaxis Driver Board Power Supply and Head
Sections
2.9
12 Motion Control Board U82 Inside CPU2 Box 2.10
13 Motion Control Board U83 Inside CPU2 Box 2.10
14 Motion Control Board U84 Inside CPU2 Box 2.10
15 HLS Center Board U85 Inside CPU2 Box 2.11
16 Linear Measure Sensor Control Board U03 Head Wiring Section 2.12
2.2 Setting of UB20 Board (Relay Board 1)
• A piece of UB20 board is used in the main body.
Refer to "1.3 Layout of BH Block" in
Chapter 13 for the location.
2.2.1 Setting of Jumper Wires
Set all Jumper Wires J23, J24, J27,
and J31 to "Short" as shown in
Fig. C2.
2.2.2 Setting of Timer
Set the time of K2 (Power ON Delay
Timer) in Fig. C2 to "1 sec".
Fig. C2 UB20
0406-001
3-2