SIPLACE Station Software 7xx to 714 介绍.pdf - 第148页
Station Software 7xx to 714.0 (R20-2) / Feature Description 11/2020 Edition 148 8.32 Placement Process for Springs Compatible mode: Not supporte d The station software provi des a new travel profile to support the placem…
Station Software 7xx to 714.0 (R20-2) / Feature Description 11/2020 Edition
147
8.29 C&P20 P Placement Head on SIPLACE X-Series S
Compatible mode: Not supported
The C&P20 P placement head was introduced for the SIPLACE X4i S placement machine in the
previous station software version. As of the current station software version, this placement head is
additionally supported on the SIPLACE X2 S, X3 S and X4 S placement machines.
The C&P20 P placement head is supported on the same locations as the C&P20 A placement
head and uses the same component camera types (23 and 41), too.
The 4xxx nozzle type is supported on all locations.
Additionally, the diagnostic method for the pressure control valve of the C&P20 P placement head
has been improved. If applicable, detailed error messages and warnings will be displayed. The
machine will be stopped if the pressure supply fails or the pressure control valve gets superheated.
8.30 WPC5/WPC6 on SIPLACE X-Serie S
Compatible mode: Not supported
The station software supports the option to put a WPC5/WPC6 with the new WPC 40 X X-table on
the X2 S, X3 S and X4 S placement machines. However, the hardware will not be released for
series production in this version.
The WPC5/WPC6 and the WPC 40 X occupy the tracks 11 – 40. Further modules, such as
X-feeders may be set up on the tracks 1 – 10.
The WPC 40 X can be selected for location 2 in the Auto Configuration. A single WPC5/WPC6
cannot be configured without the X-table. An XFCU must have been installed.
Location 2 is displayed similarly as for the SX-series placement machines with WPC in the Main
view. WPC5/WPC6 and WPC 40 X can be selected via the corresponding buttons in the Setup
view.
The Twin Head and CPP placement heads and new nozzle changer / reject bin positions are
supported for this option.
SIPLACE Smart Pin Support supports the option on the X3 S and X4 S placement machines.
8.31 SIPLACE X4i S micron – Enhancements
Compatible mode: Not supported
CPP placement head and SIPLACE JTF-M feeder
As of this SIPLACE Pro version, the CPP placement head and the SIPLACE JTF-M feeder are
supported on the SIPLACE X4i S micron placement machine.
Placement Process for Component Type 03015
When placing components of type 03015, the user is guided through a similar placement process
as for component type 01005 on the SIPLACE X4i S micron placement machine.
If the placement process 01005 is selected in SIPLACE Pro, the required process parameters such
as cameras, nozzles, travel profiles and placement forces will be set automatically.
Station Software 7xx to 714.0 (R20-2) / Feature Description 11/2020 Edition
148
8.32 Placement Process for Springs
Compatible mode: Not supported
The station software provides a new travel profile to support the placement process for springs.
Special parameters must be set in SIPLACE Pro for this placement process.
8.33 Displaying Cutting Times per Compressed Air Cylinder on the
GUI
Compatible mode: Complete
The cutting times per compressed air cylinder can be displayed on the station software GUI. Thus,
the sensor positions can be checked quickly, and the sensors adjusted if necessary.
The measurement of the cutting times is activated via the Cut button under Manual operations –
Subsystems.
Figure 8-14: Measurement of cutting times
The measured times for moving out and moving back the cylinder are displayed in a table in
milliseconds on the GUI for the left and right cylinders respectively.
The measurement only takes place within the Manual operations and not during production.
Station Software 7xx to 714.0 (R20-2) / Feature Description 11/2020 Edition
149
8.34 SIPLACE Vision Enhancements
The SIPLACE Vision system has been enhanced as follows.
8.34.1 Reading PCB Barcodes with the PCB Camera
Compatible mode: Complete
Until now, a USB dongle containing the necessary software licenses was required for reading PCB
barcodes with the PCB camera.
As of this station software version, another method may be used alternatively with which no USB
dongle is required. The feature is realized via an internal algorithm and only the software licenses
are required.
Detailed information can be found in the respective Installation Manuals to PCB Barcode, item no.
[00197222-xx] and item no. [00197413-xx].
8.34.2 Displaying Polygon Shapes
Compatible mode: Complete
Polygons are now also displayed on the SIPLACE Vision GUI.
8.34.3 Accuracy of Polygon Circles
Compatible mode: Complete
The accuracy of polygon circle features has been improved.
8.34.4 Displaying Component Shape when Teaching Local Fiducials
Compatible mode: Complete
Soldering pad patterns are used as local fiducials for components that require an exact placement
position. In this case it might be difficult to determine the center of the local fiducial. When defining
the reference point, cross hairs and quads are displayed to help aligning the reference point
manually.
Optionally, the component shape of the component that shall be placed at this position may be
displayed. The reference point of the component shape (= placement position) determines the
reference point of the taught fiducial. I.e., it is assumed that the position of the taught local fiducial
is equal to the placement position of the component in the board description.
8.34.5 Multiple Measurements with CPP Placement Head
Multiple measurements can be performed with the CPP placement head via the stationary camera
in Pick&Place mode. Thus, the component range has been extended.