SIPLACE Station Software 7xx to 714 介绍.pdf - 第62页

Station Software 7xx to 714.0 (R20-2) / Feature Description 11/2020 Edition 62 7 Feature Description – Station Software V706.x Features (V706.0 : Compatible Mode V705 ) 7.1 SX1/SX2 V2 Placement Mac hine The station softw…

Station Software 7xx to 714.0 (R20-2) / Feature Description 11/2020 Edition

Features (V705.04: Compatible Mode V704.03)

6.30 Flexible Usage of Feeder Types

As of this station software version some feeder types can be flexibly used without changing the

setup in SIPLACE Pro. After a feeder type change the machine can immediately start picking up

again.

The following feeder type pair is supported for flexible usage:

2x8mm X-feeder ↔ 8mm X-feeder

The Status display X-feeders topic has been completed accordingly in the online help of the

station software.

6.31 Enhancement of SIPLACE Smart GUI

The SIPLACE Smart GUI has been enhanced as follows:

– Optimized assistance after pick-up failure.

– New icon Waiting for PCB

This icon is displayed, if the machine waits for a board.

– New stopwatch board counter function

With this function it is possible to measure the number of produced boards in a given period of

time. A stopwatch counter and the period of time, since the measurement was started are

displayed.

The function can be started via the Stopwatch board counter button and stopped via the

Reset button in the GUI settings view.

6.32 SST38 PCB Camera Replaced by SST30

The SST30 PCB camera now covers the entire functionality of the SST38 PCB camera. Thus, it is

possible to measure 01005 components without any restrictions with the SST30 PCB camera as of

this station software version.

Features (V705.04 SP1 and SP2: Compatible Modes V704.03 SP1

and V704.03 SP2 respectively)

6.33 Improved traveling range measurement

In this station software version, the traveling range measurement has been improved. For this

reason, you are advised to recalibrate the traveling ranges during installation of the station

software.

Station Software 7xx to 714.0 (R20-2) / Feature Description 11/2020 Edition

7 Feature Description – Station Software V706.x

Features (V706.0: Compatible Mode V705)

7.1 SX1/SX2 V2 Placement Machine

The station software supports the new SX1/SX2 V2 placement machine (with one or two gantries)

in one-computer operation. The SX1/SX2 V2 placement machine only differs slightly from the

SX1/SX2 placement machine:

– Support of the new SX V2 PCB conveyor system.

– Calibration part holder at another position and consequently also the zero point.

7.2 DX4 Dual Placement Machine

The station software supports the new DX4 Dual placement machine with dual lane conveyor in

one-computer operation. The DX4 Dual placement machine only differs slightly from the SX4

placement machine:

– Head configuration with C&P20 placement heads only.

7.3 SX V2 Conveyor System

A new SX V2 conveyor system has been introduced for the SX1/SX2 V2 placement machine.

SX V2 consists of the input, processing and output sections and supports single and dual lane

conveyor.

Fixed and flexible conveyor rails and such properties as width adjustment, moving the board into

the machine etc. are, for the most part, identical to the existing conveyor system for the SX1/SX2

placement machine.

The maximum board length without the Long Board option is 450 mm and 610 mm with this

option. The maximum board width results from the fixed rail position and the conveyor mode (dual

or dual as single). The maximum board thickness is 6.5mm.

Light barriers are installed at fixed positions as stoppers for the board in the conveyor system: one

light barrier per conveyor segment (input conveyor, processing area, output conveyor and, if

applicable, intermediate conveyor). Optionally, an additional light barrier may be installed for the

Long Board option.

There are no mechanical stopper and no overlapping mapping.

Station Software 7xx to 714.0 (R20-2) / Feature Description 11/2020 Edition

7.4 Automatic Pin Positioning with Smart Pin Support

For many products it is necessary to support the board with so-called Support Pins in the

processing area. The support pins are placed on the lifting table and are kept at the defined

position by a magnet.

Manual override in the clamping area is very non-ergonomic and thus it is difficult to position the

support pins accurately by hand. Therefore an automatic pin positioning has been realized for the

SX1/SX2 V2 placement machine that is supported by this station software version. The support pin

positioning is performed by a pin picker that may position a definable number of support pins on the

lifting table. The support pin positions are defined for the recipe in SIPLACE Pro.

When the recipe is produced on the line, the support pins are automatically positioned before

production begins. Already available support pins on the lifting table may then be brought to new

positions. Missing support pins are taken from a pin magazine. If too many support pins are

available on the lifting table, they will be put back into the pin magazine. In the Setup view it is

possible to check the current support pin positions and to place or remove support pins.

Detailed information on Smart Pin Support can be found in the corresponding user manual,

item no. [00197001-01], and in the online help files to SIPLACE Pro and the station software.

Restrictions

– No collision checks in case of manual configurations on the Machine service and SIPLACE

service activity levels.

– Support pins cannot be placed before all boards in the processing area have been produced

and unloaded from the machine. Loaded boards are blocked in the input section.

– In case of barcode mode together with support pin positioning, a barcode change results in a

long changeover time, as the support pin positioning does not start until all boards have been

unloaded (except for the boards in the input section).

7.5 Revision of SSI Interface for OIS Events

The SSI interface has been revised in order to improve the support of I-Placement mode by the

OIS events. Especially, the support has been improved for the monitoring data in connection with

the "Continue production when track is empty" feature.

7.6 New SIPLACE Glue Feeder Feeder Type

The station software supports the new SIPLACE Glue Feeder feeder type. SIPLACE Glue Feeder

is an X-feeder with which glue dots can be applied onto the rear side of the component just before

the component gets placed.

The glue dots are modeled in SIPLACE Pro by defining the X-position, Y-position and the diameter

of each glue dot on the component. Multiple different glue dots can be defined for a single

component.

The process parameters of a glue dot are stored in a characteristic line at the station. The

corresponding XML file contains the glue name, the glue dot diameter, the number of shots per

glue dot, the Z-height of the jet and the fixed defined frequency of the shots.

The process parameters per glue dot are assigned at the station as follows:

Via the definition for the glue dot diameter in SIPLACE Pro the closest glue dot diameter in the

characteristic line is defined (always rounded down). The defined number of shots, the Z-height

and the frequency of the glue type are the process parameters that are passed on to the pickup

process and the SIPLACE Glue Feeder.