SIPLACE Station Software 7xx to 714 介绍.pdf - 第22页
Station Software 7xx to 714.0 (R20-2) / Feature Description 11/2020 Edition 22 3.16 Feeder Setting Comparison With this feature the feede r settings in SIPLACE Pro are compare d with the feeder settings made in the setup…
Station Software 7xx to 714.0 (R20-2) / Feature Description 11/2020 Edition
21
3.11 "Virtual PCB Stack"
The new feature "Virtual PCB Stack" allows to produce two PCBs with the same width but different
placements in one job.
In SIPLACE Pro two PCBs must be defined on one conveyor lane. During an additional
measurement each PCB is provided with a so-called “PCB Detection Inkspot”.
By means of this inkspot the PCBs differ from each other and by means of this marking the station
loads the accurate placement program.
Restrictions
No plausibility check is performed. I.e., if both inkspots are detected by mistake, both board
contents will be placed. If neither of the two inkspots is detected, no placement will be performed.
3.12 Extension of the Form Editor (SIPLACE Vision)
The Form editor view of SIPLACE Vision has been extended as follows:
– Collinearity check
– Lead length and width inspection for CHIP components
– Face Down Recognition for further component types
– New lead type "rectangle"
– Separate group description may be activated at the station
A detailed description of the SIPLACE Vision functions can be found in the online help of the
station software.
3.13 Auto Configuration
The "Auto Configuration" feature has been implemented in the station software to support multiple
configurations for different types of machines, heads, conveyors etc. The station software detects
the type of hardware constituting the machine and configures itself accordingly. On the GUI the
operator is prompted to confirm the auto configuration and, if necessary, a download of the
appropriate embedded software.
3.14 Reduced Air Consumption with Vacuum Pump
X-series machines with C&P20A placement heads can optionally be operated with a vacuum pump
in order to reduce the air consumption. For this, the machine must be equipped with a retrofit kit.
Detailed information can be found in the "X-Series Retrofit instructions", item no. [00195089-xx].
3.15 Screen Saver
A screen saver has been integrated in the station software to protect the screen against sticking
effects. "Sticking effects" signify an always visible pattern displayed on the screen, caused by
statical images or capacity overload. If no entries are made during a defined space of time, the
screen saver starts, and a vertical line is moving from the left to the right. As soon as an entry is
made (mouse movement or keyboard input) the screen saver stops, and you can go on working
where you stopped before.
Station Software 7xx to 714.0 (R20-2) / Feature Description 11/2020 Edition
22
3.16 Feeder Setting Comparison
With this feature the feeder settings in SIPLACE Pro are compared with the feeder settings made
in the setup. In case of differing values, a warning is displayed, the feeder is deactivated and via
the GUI the operator is prompted to confirm the changed values or continue with the values from
SIPLACE Pro. This is to avoid that feeder settings (such as pickup position, feeder pitch) are
changed unintentionally. However, no confirmation is required if the feeder settings are changed
directly on the GUI.
The comparison is performed in the following cases:
– Immediately after a job download.
– When feeder settings are modified directly on the feeders after a job download.
– When one or several feeders are exchanged during production.
Station Software 7xx to 714.0 (R20-2) / Feature Description 11/2020 Edition
23
4 Feature Description – Station Software V703.x
Features (V703.01)
4.1 X4i with New Electronic Concept
Additionally to the X-series placement machines, the station software supports the X4i placement
machine with the new HCU (Head Control Unit) / GCU (Gantry Control Unit) electronic concept in
one-computer operation. Due to a changed camera position, an alternating placement mode is
possible for all conveyor configurations and for single conveyor on this placement machine.
4.2 SX1/SX2 placement machine
The station software supports the new SX1/SX2 placement machine (with one or two gantries) in
one-computer operation. The special features of the 703 station software for the SX-series are
listed in section 4.11 to section 4.24.
4.3 C&P20 Placement Head
The station software supports the C&P20 placement head on the X2, X3 and X4 placement
machines.
4.4 Fast Head Exchange – Separating Component Camera from Head
As of this station software version the camera can be separated from the placement head.
4.5 2x8mm X-Feeder
The station software supports the 2x8mm X-feeder.
4.6 "IPTE Multi Stick Feeder"
The station software supports the "IPTE Multi Stick Feeder". There are two models of this feeder:
– IPTE multi stick 60 AX
– IPTE multi stick XL80 AX