SIPLACE Station Software 7xx to 714 介绍.pdf - 第231页
Station Software 7xx to 714.0 (R20-2) / Feature Description 11/2020 Edition 231 12 Feature Description – Station Software V711.x Features (V711.0 (R17- 2) : Compatible Mode 710.2) 12.1 "The Hermes Standard" – N…
Station Software 7xx to 714.0 (R20-2) / Feature Description 11/2020 Edition
230
11.24 Miscellaneous Improvements and Adaptions
11.24.1 Audible Signal for Indicator Lamps – New Pulse State
Compatible mode: Complete
The audible signal for the indicator lamps has been enhanced and now supports three states: On,
Off and Pulse (new). The Pulse state is like the lamp indicators flashing state.
Allowed pulse values: 50 ms on, 950 ms off.
The audible signal can be switched off in the Production view on the station software GUI.
11.24.2 Station Software GUI – Adaptions
Compatible mode: Complete
– For the following detailed errors, a button in the message bar is offered to confirm the error
directly:
40022 Position of dispenser nozzle has not been measured
40040 Reject plate must be empty
40039 Reject plate is full
40033 Prerequisites for changing lane width …
40025 Inspection of dispenser nozzle failed
– When the top side of a component is taught, the wizard will be offered instead of the SIPLACE
Vision teaching page.
Station Software 7xx to 714.0 (R20-2) / Feature Description 11/2020 Edition
231
12 Feature Description – Station Software V711.x
Features (V711.0 (R17-2): Compatible Mode 710.2)
12.1 "The Hermes Standard" – New Communication Protocol
Compatible mode: Partly compatible
"The Hermes Standard" is a new communication protocol for SMT assembly lines that can be used
alternatively to the electrical SIPLACE SMEMA interface. With this protocol, more information can
be transferred with the board down the line like unique board Ids, barcodes, conveyor speed, board
length / width / thickness. All this information can be transferred down the complete line, without
any interruption. Up to now, this was only possible within a SIPLACE SMEMA cluster. If all devices
in the line support "The Hermes Standard", whispering down the line is possible within "The
Hermes Standard" cluster as it is within the SIPLACE SMEMA cluster.
"The Hermes Standard" is supported on the X-series S, TX-series and TX micron-series placement
machines.
The sequence of machines and devices (SIPLACE, ASYS, others) must be configured in SIPLACE
Pro so that every machine / device in the production chain knows about its next and previous
device per transport lane including their according IP-addresses.
The hardware options (activate peer, host, IP address) related to "The Hermes Standard" can be
configured on the station software GUI in the "The Hermes Standard" configuration dialog under
Service – Configure machine – "The Hermes Standard".
Figure 12-1: "The Hermes Standard" configuration dialog
Station Software 7xx to 714.0 (R20-2) / Feature Description 11/2020 Edition
232
For diagnostic purposes, a view has been added to the Event tool. For each "The Hermes
Standard" end-point, a tab page is displayed, listing the received and sent messages. Only the last
100 messages after the GUI started are displayed.
If all devices between the first and the last SIPLACE station use "The Hermes Standard",
whispering of the station-wise download is supported even if 3
rd
-party equipment is setup in
between the SIPLACE devices. The user only has to confirm the changeover at the first SIPLACE
station but no longer at the SIPLACE station after the AOI system.
Restrictions
– No support for stations with shuttle.
– No support for devices with IPv6 addresses.
12.2 New Placement Force – Very Low Force in Placement, Pickup and
Dipping Processes
Compatible mode: Hidden
The new very low placement force (0.5 N) for pickup, placement and dipping is supported by the
station software. The very low force state must be set in SIPLACE Pro and can be enabled for the
following placement heads: C&P20 M2, C&P20 P and (from R18-1) C&P20 P2.
All segments of the concerned placement heads will be measured when the first board enters the
machine to check which segments are able to handle this hardware requirement. The results are
displayed in the new Very low force column of the list in which the height values of the nozzles are
displayed (Manual Operations – Subsystems – Gantry n –x Head – Segments – Height
values).
Additionally, the measurement can be performed in the Maintenance view under Test bench
inspection with the measurement step Z axis movement.
12.3 SEMO CRF80 – New Tape Feeder
Compatible mode: Hidden
The new SEMO CRF80 tape feeder from the SEMO company is supported by the station software
and occupies seven tracks on the X-table. The feeder is distributed directly by the manufacturer.
12.4 SIPLACE TX micron-Series – Teaching
Compatible mode: Complete
The station software provides a function to teach the distance between standard stop position and
light barriers of the vacuum tooling of a TX micron placement machine. The light barrier is modelled
as backward stopper. The position of this backward stopper is provided as teachable position and
can be taught like the standard forward stopper ("teaching the reference corner"). Instead of
teaching the front right corner of the board, the back corner to the right is used to teach the
backward stopper.
The default value of the distance between standard stopper and backward stopper is substituted by
the measured value.