00197395-03_AI_3D_Sensor-Koplan_X-Serie_S_DE_EN.pdf - 第148页

4 Appendix 4.3 Excerpt from the assembly instructions "SIPLACE X-Series S - stationary camera type 25/33" [00197397‑xx] 148 Assembly Instructions / Montageanleitung SIPLACE X-Series S 3D-Sensor 06/2020 Coding t…

100%1 / 158
4 Appendix
4.3 Excerpt from the assembly instructions "SIPLACE X-Series S - stationary camera type
25/33" [00197397‑xx]
Assembly Instructions / Montageanleitung SIPLACE X-Series S 3D-Sensor 06/2020 147
4.3.1.1 Adjusting the Camera Jumper Setting
NOTICE
Coding the DIP switch
IC cameras of type 33 up to version 07 are equipped with an 8-pin DIP switch. IC cameras
of type 33 from version 07 are equipped with a 6‑pin DIP switch.
Fig.107: Setting the DIP switch – example of 6-pin switch
shown
► Remove the lighting unit and the cover
from the camera.
► Set the DIP switch (1) at the camera,
according to the configuration and DIP
switch type (see section 4.3.1.1.2
"Cod-
ing the DIP Switch (6 Pin)" [}148]or
4.3.1.1.1
"Coding the DIP Switch (8
Pin)" [}147]).
► Make a note of the jumper setting on the relevant label on the camera housing.
NOTICE
Exchanging the camera housing when there is more than one camera
When fitting the cover and the lighting unit, make sure that this is not confused with the one
for a different camera.
Coding the DIP Switch (8 Pin)
Fig.108: Setting the DIP switches
► Set the DIP switch (1) on the camera.
S Setting for gantry* Comments
1 2 3 4
1 OFF OFF OFF OFF Boot
2 OFF OFF OFF OFF Reset
3 OFF ON OFF ON Gantry ID 0
4 OFF OFF ON ON Gantry ID 1
5 OFF OFF OFF OFF Test
6 OFF OFF OFF OFF CAN terminator
7 ON ON ON ON 1 Mbit/s
8 x x x x x x x x x = OFF: FC camera (type 25)
x = ON:
IC camera (type 33/36)
* Not all gantries may be available, depending on the machine type.
4 Appendix
4.3 Excerpt from the assembly instructions "SIPLACE X-Series S - stationary camera type
25/33" [00197397‑xx]
148 Assembly Instructions / Montageanleitung SIPLACE X-Series S 3D-Sensor 06/2020
Coding the DIP Switch (6 Pin)
Fig.109: Setting the DIP switches
► Set the DIP switch (1) on the camera.
DIP switch S1 for SST25 and SST33
Switch Status Signal name Description
S1.1 OFF VCU_CODE OFF: normal operation
ON: Reset
Location 1 Location 2 Location 3 Location 4
S1.2 ON/OFF *) PORTAL_ID_0 OFF ON OFF ON
S1.3 ON/OFF *) GANTRY_ID_1 OFF OFF ON ON
S1.4 OFF SMD_LED OFF: standard LED
ON: SMD LED
S1.5 OFF CAN_H OFF: with CAN terminator
ON: without CAN terminator
S1.6 ON/OFF CAN_GROUP OFF: FC camera
ON: IC camera
4.3.1.2 Fitting the IC Camera Type 33
The camera is fixed at two spacer plates, which have already been screwed to the screw fixing
points on the machine base.
The procedure for fitting these spacer plates and for fixing the cameras is in principle the same at
all locations. Any differences are indicated in the following section.
► Before installation, make sure that the jumper setting for the camera to be fitted is correct (see
4.3.1.1
"Adjusting the Camera Jumper Setting" [}147]).
See also
2 4.3.1.2.2 "IC Camera Type 33: Fixing the Camera Module" [}152]
4 Appendix
4.3 Excerpt from the assembly instructions "SIPLACE X-Series S - stationary camera type
25/33" [00197397‑xx]
Assembly Instructions / Montageanleitung SIPLACE X-Series S 3D-Sensor 06/2020 149
Fitting the Spacer Plates
The spacer plates are fixed to the relevant screw fixing points in the machine base. Narrow spacer
plates are used at locations 2 and 3, while wide spacer plates are used at locations 1 and 4.
Screw fixing points at location 2 and 3
Fig.110: Screw fixing points at location 2 (left) and 3 (right)
1. Screw fixing points for the reject bin
2. Screw fixing points for the IC camera type 33
3. Screw fixing points for the IFC camera type 25
The screw fixing points at location 2 and 3 are mirrored. Use the left holes at location 2.
Screw fixing points at location 1 and 4
Fig.111: Screw fixing points at location 1 (left) and 4 (right)
1. Screw fixing points for the IC camera type 33